Dependable Plumbing in Danville, KY

Installed a 10-ton used rooftop package unit on commercial building roof with knockdown flat roof curb. Fabricated and installed supply and return duct drops to connect unit to interior space, completing the HVAC system installation for the commercial facility.

Completed preventive maintenance tune-up on geothermal HVAC system with indoor unit located in attic and outdoor unit in basement. Inspected both units and documented significant corrosion present on copper refrigerant lines, metal housings, and manifold components, indicating prolonged moisture exposure and system age. Noted extensive rust and oxidation on piping, connections, and metal channels throughout both the basement and attic equipment, with particular deterioration at pipe bends and fittings. Performed standard maintenance procedures including system inspection and operational testing. Customer provided filters as arranged. Advised customer of advanced corrosion conditions observed on multiple system components that may require future attention to prevent potential system failures or refrigerant line integrity issues.

Responded to warranty call for recently installed HVAC system that would not power on and displayed orange triangle error on Honeywell thermostat. Performed diagnostic testing using Fieldpiece SMAN manifold gauge, verified refrigerant pressures and system charge on FR454B refrigerant, confirmed proper system operation with cooling mode activated and pressures within normal range. System restored to full functionality with thermostat displaying correct temperature readings and cooling status.

Completed commercial HVAC ductwork installation in unfinished commercial building space per approved plans. Supplied and installed all specified supply and return ductwork with reflective insulation throughout facility, including rectangular and cylindrical duct transitions suspended from exposed ceiling structure. Installed complete bathroom exhaust ductwork system. Coordinated crane services to successfully set two 7.5-ton rooftop units on building roof. Installed all grilles, registers, and diffusers as specified in project drawings. Secured all necessary permits and completed required inspections. All ductwork properly insulated and secured to structural members using appropriate hangers and supports. System ready for startup upon completion of gas piping and electrical connections by others. Project represents second phase of three-phase installation with one-year warranty on all supplied materials and labor following initial startup.

Serviced dual shower head system with Kohler fixtures in master bathroom. Accessed and repaired malfunctioning valve assembly on first fixture that was not operating properly, replacing internal cartridge components. Adjusted temperature limiting stop on second fixture to increase hot water output and restore proper temperature balance.

Completed scheduled maintenance visit on four heat pump split systems as part of planned service agreement. Performed comprehensive inspection of all units, including electrical component testing with multimeter to verify proper capacitor function and system performance readings. Conducted thorough examination of refrigerant line connections, electrical terminals, and heat exchanger coils on all four systems to ensure optimal operation and identify any potential issues requiring attention.

Completed biannual preventive maintenance on fifteen-year-old residential air conditioning system. Performed comprehensive tune-up including electrical diagnostics with multimeter reading 497.5 volts, temperature verification across evaporator coil measuring 52.9°F at insulation surface, inspection of furnace and cooling components, and standard safety checks. All equipment operating within normal parameters; system ready for continued service.

Responded to non-urgent service call for propane-fueled HVAC system requiring reset after customer refilled propane supply. Accessed unit in unlocked basement, performed system reset to restore proper gas operation, and inspected existing air filter (18x24x2) to ensure proper installation and adequate airflow through the furnace system.

Successfully removed existing galvanized line underneath bathroom faucet and installed new shut-off valve, ensuring proper functionality. Installed customer-supplied Smith 530 water heater with digital control panel, connecting all necessary copper piping and completing electrical connections in the utility area.

Performed scheduled care plan tune-up on heat pump system with air handler located in basement. Conducted electrical diagnostics using a clamp meter to verify proper amperage draw on the system. Connected manifold gauges to outdoor unit to check refrigerant pressures and system operation parameters, confirming all readings within manufacturer specifications.

Diagnosed low water pressure issue in bathroom fixture, identifying calcium deposits in supply lines and partial blockage in the drain assembly. Inspected the 50-gallon Rheem water heater in garage utility closet, finding it was functioning properly but noted water damage and possible mold on wall surrounding bathroom plumbing penetrations. Cleaned affected drain components and recommended replacement of corroded supply lines to restore proper water pressure and flow.

Performed maintenance service on a relatively new club single HVAC system located in the garage attic. Inspection revealed dust accumulation on the evaporator coil fins requiring cleaning. Replaced the 14x25x1 air filter and renewed customer's Gold maintenance plan.

Performed scheduled Care Plan Tune Up on two AC units connected to oil furnaces, including replacement of nozzles (.85 80°B) and oil filters (General 2A-710). Upon inspection, identified significant corrosion on metal components and investigated noise concern reported by customer. Materials were on-site as pre-arranged. Note: Service was limited to the two AC systems directly connected to oil furnaces as specified in maintenance agreement.

Performed scheduled Care Plan tune-up on AC/GF system located in crawl space. Conducted electrical testing with Fluke 376 FC clamp meter, measuring amperage draw at 0.9A and verified capacitor function on the TITAN PRO unit. System operating at proper temperature parameters with readings showing 58 degrees, indicating normal operation.

Performed diagnostic service on 8-year-old Lennox gas heating system that was inoperative following customer-reported clanking noises. Inspection revealed issues with the heat exchanger and connection points within the system. Thoroughly cleaned components and restored proper operation after verifying adequate fuel supply.

Successfully installed a complete Bryant HVAC system consisting of an 80% efficient 70K BTU gas furnace (800SB36070M14), 2-ton 14.3 SEER2 air conditioning unit (GA5SAN52400W), and matching 2-ton evaporator coil (CVAVA2414XMA). Installation included all required connections, safety components, and verification of proper system operation while utilizing the existing thermostat.

Responded to no heat call for 2-year-old heat pump system. Diagnostic testing revealed system was attempting to operate on auxiliary heat mode due to customer being out of propane. Temperature readings confirmed 61° indoor temperature with thermostat set to 70°. Verified proper operation of electrical components and reset system to restore heat function.

Replaced leaking section of copper water supply line through concrete block wall. Installed new copper piping with proper fittings and shut-off valve. Completed penetration through wall and floor to ensure proper installation and eliminate leak.

Performed scheduled Care Plan maintenance on geothermal HVAC system in crawlspace. Conducted comprehensive diagnostics including temperature readings with Klein Tools ET05 thermometer and electrical load testing with Fluke 376 FC clamp meter (6.1A reading). Replaced filter as per quarterly maintenance schedule and ensured crawlspace light was turned off and door secured upon completion.

Performed scheduled Care Plan tune-up on AC and gas furnace located in garage. Inspected furnace burners showing proper blue flame pattern and combustion. Replaced customer-supplied air filter which showed moderate dust accumulation. System operating normally with no issues identified.