24/7 Emergency HVAC in Midway, KY

Installed customer-supplied bathroom vanity fixtures, including an integrated sink basin, single-handle faucet, and pop-up drain assembly, in the basement bathroom where the rough-in plumbing was previously completed. Verified secure connections, proper drain stopper operation, and a clean, undamaged basin upon completion.

Performed a seasonal tune-up on the Carrier gas furnace and evaporator coil system, including inspection of the blower assembly, which showed dust and grime buildup on the squirrel-cage blades and housing. Verified condensate drainage through the PVC line and condensate pump, and checked the gas line and duct connections. Customer-supplied pleated air filter was on site for installation.

Performed a single-system maintenance visit on a basement-installed heat pump and gas furnace (dual-fuel) system, inspecting the furnace, indoor coil cabinet, refrigerant line set insulation, condensate drain line, and supply duct connections. Replaced the air filter with the customer-provided 24x25x4 media filter and verified the system was operating properly with no visible rust, frost, or damage.

Performed scheduled maintenance on a Friedrich ductless mini-split heat pump system, inspecting the outdoor condenser's electrical compartment and confirming secure terminal block connections (L1, L2, 1(N), 2(L), 3(S)), proper wire routing, and intact conduit and cable entries. Verified the unit is A2L refrigerant-rated with warning labels present, and found the condenser properly mounted on brackets with no signs of frost, rust, or physical damage.

Completed comprehensive Club Duo maintenance on geothermal heat pump system and air handler. Performed standard tune-up procedures including inspection of electrical components, capacitor testing and evaluation, filter assessment (washable filter and customer-provided Aprilaire #510), and verification of Aprilaire #800 steam humidifier canister condition. All system components inspected and found operating within normal parameters.

Completed Gold Level preventive maintenance on single-zone HVAC system including gas furnace and air conditioning unit. Performed comprehensive inspection with burner operation verified showing proper flame characteristics and combustion, temperature differential measurements recorded at 5.23 degrees, and photographic documentation captured of all critical components including heat exchanger, burner assembly, and gas valve system.

Responded to no cooling complaint on 8-year-old Rheem electric central air conditioning system. Thermostat set at 68°F but indoor temperature reading 75°F. Confirmed adequate airflow from supply vents but air temperature not cooling properly. Performed diagnostic evaluation of outdoor condensing unit and indoor air handler located in utility closet. Inspected condenser fan operation, refrigerant levels, and electrical components on outdoor unit. System required repair to restore proper cooling capacity and bring indoor temperature to setpoint.

Replaced defective defrost control board and contactor on heat pump system under parts warranty. Performed nitrogen leak test on outdoor unit due to previous leak history on outdoor pressure switch that was replaced in 2023. Parts were picked up from Ferguson supply house, installed, and system was tested for proper operation. All electrical connections were secured and verified for safety and functionality.

Completed comprehensive plumbing rough-in installation for two bathroom renovation project. Installed new sewage ejector pump and verified proper functionality before departure. **Bathroom A (Shower):** Jackhammered concrete flooring to access drainage area. Installed new P-trap assembly with stub-up for shower base connection. Ran and stubbed out Uponor water supply lines for lavatory, toilet, and shower connections. Installed Delta universal rough-in shower valve with Uponor fittings per specifications. **Bathroom B (Tub & Shower):** Ran complete Uponor water supply lines for lavatory, toilet, and tub/shower valve connections. Installed Delta universal rough-in tub/shower valve with Uponor fittings. Set new shower base and installed tub/shower wall panels. Ran stub-out for lavatory drain connection. All water supply lines installed using new Uponor PEX piping system with hot and cold lines properly color-coded and secured to framing. All rough-in valves and drain connections teste

Responded to callback for system not maintaining setpoint following previous maintenance visit. Upon arrival, thermostat displayed 78°F with setpoint of 72°F, indicating 6-degree temperature differential. Performed diagnostic evaluation of cooling system operation and measured supply air temperature at 57.4°F using calibrated psychrometer, confirming adequate cooling output from evaporator coil. Investigated potential airflow restrictions, refrigerant charge levels, and system cycling patterns to identify cause of insufficient cooling capacity.

Conducted on-site plumbing estimate for basement bathroom fixture installations where rough-in plumbing was already completed. Assessed existing PVC drain lines, water supply lines including PEX tubing, and structural framing to determine scope of work needed for final fixture hookups. Customer will complete their own drywall finishing and fixture placement, requiring estimate for connection of toilets, sinks, and bathing fixtures to the pre-installed rough plumbing infrastructure.

Responded to no cooling call for dual-zone electric HVAC system with 5-year-old equipment. Customer reported both upstairs and downstairs systems were not operating and not communicating with each other. Upon arrival, performed diagnostic evaluation of outdoor condensing unit and accessed electrical control panel to inspect internal components, circuit boards, transformers, capacitors, and wiring connections. Documented system condition with photos showing control board configuration, power distribution components, and overall electrical assembly. Customer had replaced filters prior to service call. Further diagnostics required to determine communication failure between zones and restore cooling operation to both systems.

Completed preventive maintenance tune-up on heat pump system including both outdoor condensing unit and indoor air handler. Performed comprehensive system diagnostics using clamp meter to verify electrical parameters, measured voltage and amperage readings, inspected 24-volt control circuit, and documented equipment condition with photos per club membership agreement.

Completed attic ductwork repair utilizing two technicians over a four-hour period. Installed six sheets of double joist panning metal to properly cap and seal exposed ductwork sections. Applied foil-backed insulation to air handler unit and associated ductwork to improve thermal efficiency and prevent condensation issues in the attic space.

Responded to service call for thermostat unable to maintain set temperature of 72°F, with room remaining at 68°F. Upon arrival, accessed attic space to inspect HVAC system and air handler unit. Discovered significant deterioration of condensate drain pan with large crack running through center, causing structural failure and potential water drainage issues. Identified damaged and deteriorating duct insulation on primary supply duct with torn sections, frayed edges, and exposed underlying material compromising system efficiency. Documented all findings with photographs showing extent of damage to both drain pan and duct insulation. Advised that compromised drain pan poses risk of water damage and must be replaced, and damaged insulation is causing heat loss/gain affecting system's ability to maintain desired temperature. Recommended immediate replacement of cracked drain pan and re-insulation of damaged ductwork to restore proper system operation and temperature control.

Responded to service call for toilet running continuously and producing whistling noise, resulting in excessive water consumption. Upon inspection, found discolored water in tank indicating mineral buildup and potential fill valve malfunction. Diagnosed faulty fill valve as primary cause of running water and whistling sound, with additional concerns regarding water quality and internal component condition requiring attention.

Performed routine maintenance on an 18KW Generac residential standby generator connected to propane fuel supply. Conducted comprehensive system inspection including visual assessment of generator housing, transfer switch components, and electrical connections. Documented unit condition with photographs showing proper installation on concrete pad, adequate clearances from structure, and secure propane tank proximity. Inspected transfer system data label and verified neutral bonding configuration within automatic transfer switch panel. Confirmed all wire terminations at neutral bus bar were secure and properly organized. Checked control module LED indicators and system status lights for proper operation.

Completed scheduled Care Plan tune-up on geothermal HVAC system with washable filter. Performed diagnostic testing using digital clamp meter, recording amperage readings of 16.3A and 71.4A to verify proper system operation. Confirmed Air Scrubber air purification unit, installed in November 2022, is functioning correctly with LED indicator illuminated and integrated properly within the ductwork system.

Completed full residential HVAC system replacement including installation of Lennox Elite Series 18 SEER2 variable capacity air conditioner (Model EL18KCV-036), Lennox Dave Signature Series 80% AFUE 90,000 BTU variable speed furnace (Model SL280UH090V48BK), and matching evaporator coil (Model CK40CT-036B-71). Removed and properly disposed of existing equipment per code requirements. Installed outdoor condensing unit on concrete pad with electrical whip kit, disconnect box, and insulated refrigerant lines with filter drier. Mounted unit against exterior wall with properly secured black conduit for electrical connections. Indoor installation included furnace with variable speed blower, evaporator coil with transition fittings to existing ductwork, and standard air filter rack. Connected unit to existing flue piping with flame rollout protection. Installed flexible gas line connector with gas shutoff switch and electrical shutoff switch per code. Modified basement return air ductwork to

Conducted comprehensive equipment assessment for dual-system HVAC replacement estimate at residential property. Evaluated existing 10-12 year old Trane equipment with one indoor unit located in attic and second unit in basement. Documented current system conditions through photographic documentation of mechanical room showing condensate drainage configuration, ductwork insulation, and equipment accessibility. Assessed interior supply vent locations and distribution system. Provided replacement options focusing on Trane equipment specifications to match customer preference and discussed financing availability for immediate replacement needs.