Trusted Home Services in Harrodsburg, KY

Installed a new 100-amp panel with branch circuit breakers (including additional single-pole and 2-pole units) and wired the outbuilding with GFCI and duplex receptacles, four single-pole switches, a weatherproof receptacle, and a 30-amp 240V receptacle with cover. Roughed in cable runs and boxes for four 4" LED wafer lights, two exterior sconces, and a chandelier (wiring only, for customer to hang). Rough-in was completed for inspection, with a return trip to be made to install devices and finish the work.

Performed a Gold Level maintenance on a single-system electric split with the indoor unit in an unfinished basement, including inspection of the evaporator coil, which showed light dust and grime buildup with minor fin compression and no signs of frost, ice, or standing water. Verified system performance on R410A using digital manifold and temperature probes: vapor saturation temp of 42.8°F (124.8 psi), liquid saturation temp of 95.6°F (298.9 psi), superheat of 15.2°F, and subcooling of 8.5°F, with supply/return temperatures of 58.0°F and 87.1°F. Readings indicate the system is operating within normal parameters.

Completed electrical rough-in installation for commercial space under construction, installing GFCI receptacle, standard duplex outlet, single-pole switch, and keyless light fixture with bulb in vaulted ceiling area. All materials stocked and installed per code requirements including SJ cord with male cord cap, with outlets and switching devices properly mounted to exposed framing in preparation for final wall finishing.

Completed full electrical installation for a 12x24 commercial structure, installing all outlets at 36-inch height per specifications. Installed and wired a 100-amp main electrical panel with two breakers, one GFCI receptacle, two duplex outlets, one single-pole switch, and one keyless light fixture with bulb. Ran metal conduit from the main panel and established proper grounding and circuit protection throughout the structure. All electrical work was completed in the rough-in phase within the exposed framing, with wiring routed through studs and appropriate junction boxes mounted to structural members. Installation passed required electrical inspection, and a return trip was made to complete final trim-out and finishing work after wall coverings were installed.

Completed electrical installation in unfinished structure including one GFCI receptacle, one standard duplex receptacle, one single-pole switch, one keyless light fixture with bulb, and one SJ cord with male cord cap. All devices were installed per code requirements with proper wiring connections, and the installation was verified for functionality in the new construction environment.

Completed electrical rewire and device installation for barn structure, including installation of 100-amp main panel with three breakers, two GFCI outlets, two standard duplex receptacles, two switched duplex outlets, and two single-pole switches throughout the building. Ran 240V 30-amp feeder circuit from main residence panel to new barn subpanel, establishing independent power supply to the outbuilding with proper overcurrent protection and grounding.

Completed electrical estimate for running power from existing residential service panel to new barn structure located approximately 150-200 feet from main house. Assessed current electrical service capacity at main dwelling, which includes 200-amp meter base with weatherproof disconnect and properly grounded service entrance. Evaluated optimal routing path across property from house-mounted service equipment to barn location, accounting for underground conduit burial requirements and clearance specifications. Determined wire gauge requirements and conduit sizing based on anticipated barn electrical load and voltage drop calculations over distance. Specified materials including appropriate AWG copper conductors, PVC conduit for underground installation, weatherproof junction boxes, and barn-side sub-panel with adequate circuit capacity for lighting, receptacles, and potential equipment loads.

Completed comprehensive electrical rough-in and finish installation for commercial structure, including installation of 100-amp main service panel equipped with three single-pole breakers and one two-pole breaker. Installed complete wiring system throughout framed structure consisting of four GFCI receptacles, four duplex outlets, four single-pole switches, two keyless fixtures with bulbs, one ceiling fan with integrated lighting, two LED recessed can lights, and one LED dusk-to-dawn security flood fixture. Installed dedicated 240V 30-amp receptacle for HVAC equipment per code requirements. Work completed in two phases with initial rough-in inspection performed prior to return trip for trim-out and final device installation.

Completed complimentary plumbing inspection in coordination with HVAC service appointment. Performed visual inspection of bathroom fixtures including toilet and under-sink plumbing assembly, verifying proper installation of garbage disposal unit, P-trap configuration, water supply lines, and drain connections. All components found in satisfactory operating condition with no leaks or immediate concerns identified.

Responded to callback for rising indoor temperatures following previous plenum reinstallation work. Upon arrival, homeowner reported hearing a loud popping sound the night before, with indoor temperature climbing into the 80s. Inspected evaporator coil and air handling system components for potential issues related to the reported noise and loss of cooling capacity. Documented current condition of heat exchanger coils and surrounding ductwork with photographic evidence showing operational equipment with normal wear patterns and minor dust accumulation on finned surfaces.

Completed full electrical installation for 12x20 commercial outbuilding over two service visits including rough-in and finish work. Installed 100-amp main service panel with three breakers for 120V, 115V, and HVAC circuits. Wired and mounted one GFCI receptacle, three duplex receptacles, one weatherproof receptacle with cover at entry doors, and one 240V 30-amp receptacle for HVAC equipment per manufacturer specifications. Installed four single-pole switches controlling four 4-foot LED strip lights, one ceiling fan with integrated lighting, and one dual-head motion-activated LED flood light centered above doorway. All installations completed to code specifications and passed final inspection.

Completed full electrical wiring installation in 10x26 outbuilding structure, installing 100-amp main service panel with breakers, GFCI outlet, duplex receptacles, single-pole switch, and keyless light fixture with bulb. Ran all necessary branch circuits through exposed framing, mounted panel centrally on OSB wall with proper conduit connections, and installed outlet boxes per code requirements. All electrical components tested and verified operational upon completion.

Responded to no cooling complaint on 4-year-old electric HVAC system with indoor temperature reading 87°F against thermostat setpoint of 80°F. Upon inspection, discovered outdoor condenser unit with severely restricted airflow due to extensive debris accumulation on condenser coil and protective grilles. Filter screens were completely obstructed with matted grass clippings, dirt, dust, and organic material buildup, preventing proper heat exchange and causing system to run continuously without adequate cooling capacity. Removed access panels and extracted heavy layer of compacted debris from condenser coil fins and surrounding protective screens. Cleaned condenser coil thoroughly to restore airflow and heat transfer efficiency. Inspected fan motor operation and verified proper rotation. Noted indoor air filter in crawlspace location had not been changed since system installation in May 2022, contributing to overall system inefficiency. Recommended immediate replacement of 16x20x4 indoor

Completed electrical rough-in installation for new construction outbuilding, installing GFCI receptacle, standard duplex outlet, single-pole switch, keyless light fixture with bulb, and SJ cord with male cord cap. Routed black electrical cable vertically through wall cavities between studs, mounted outlet boxes to framing members per code requirements, and verified all connections prior to insulation and drywall installation.

Completed Club Duo maintenance service on heat pump and air handler system located in crawlspace. Performed comprehensive inspection of both indoor and outdoor units. Examined heat exchanger coils and condenser fins, noting dust accumulation and minor discoloration on finned components. Inspected metallic ductwork connections and verified proper installation. Assessed evaporator coil assembly and U-bend refrigerant tubing for proper configuration. Examined drain pan beneath air handler, observing mineral deposits, staining, and moisture residue indicating normal condensate drainage activity. Documented equipment condition through photographs for maintenance records. System components showed typical operational wear consistent with regular use.

Completed electrical installation in new construction outbuilding, including installation of 100-amp main electrical panel with two circuit breakers, one GFCI receptacle, two duplex receptacles, one single-pole switch, and two keyless light fixtures. All wiring and devices installed per code requirements in the unfinished structure with exposed OSB sheathing and structural framing.

Installed new black ceiling fan with integrated light fixture in outdoor gazebo structure. Ran electrical wiring through exposed beam ceiling framework, mounted fan securely to structural support, and tested all functions including fan operation at multiple speeds and lighting controls to ensure proper performance in covered outdoor environment.

Completed full electrical installation in unfinished structure including 100-amp main panel with breakers, GFCI and duplex receptacles, single-pole switches for lighting control, recessed LED wafer cans, keyless porcelain fixture, and ceiling fan with integrated light fixture. All wiring was run through exposed framing, panel was mounted and energized, and all devices were installed and tested for proper operation per NEC standards.

Responded to service call for leaking shower/tub valve issue. Upon inspection, identified failed diverter assembly components causing water leak. Removed and replaced defective plastic float mechanism and brass cartridge retainer from tub spout diverter valve. Photographed failed parts showing wear and deterioration of internal valve components. Tested system operation after replacement to verify proper function and confirm leak resolution.

Completed electrical installation for stock building 10x161, installing a 100-amp service panel with two breakers, one GFCI receptacle, two duplex receptacles, one single-pole switch, and two keyless light fixtures with bulbs. Ran conduit and wiring through framed structure during construction phase, mounting junction boxes in vaulted ceiling area and throughout the space. All components installed to code specifications with proper grounding and circuit protection in place for the commercial structure.