Heating, Air Conditioning, Geothermal, Electrical and Plumbing Experts in Cynthiana, KY

Completed care plan tune-up on geothermal HVAC system located in basement. Performed standard maintenance procedures including system diagnostics, pressure testing of refrigerant lines, and verification of proper operating parameters. Customer provided their own filter for the service visit.

Completed 65-point whole home plumbing inspection and tanked water heater flush service. Performed comprehensive evaluation of all accessible plumbing fixtures, supply lines, drain systems, and shut-off valves throughout the residence. Inspected bathtub and shower enclosure, verifying proper drainage function and examining visible plumbing connections. Checked under-sink plumbing components including supply lines, P-traps, and shut-off valves for leaks or deterioration. Conducted complete tanked water heater flush to remove sediment buildup and maintain optimal heating efficiency. Attached drain hose to tank drain valve, opened valve to discharge water and accumulated mineral deposits until water ran clear. System restored to normal operation with all components functioning properly.

Responded to callback for tilted outdoor HVAC unit. Upon arrival, used level to assess condenser positioning and confirmed unit had settled and was no longer level. Documented current condition of RUUD outdoor unit with photographs showing degree of tilt and positioning in relation to pad. Unit requires releveling or pad adjustment to prevent potential compressor damage and ensure proper refrigerant flow and drainage.

Responded to intermittent water leak originating from upstairs bathroom and affecting downstairs bathroom ceiling. Accessed wall cavity and identified water-stained structural components and plumbing connections. Located source of leak at supply valve assembly between floor joists, where brass valve fitting and PVC pipe connections showed evidence of moisture infiltration and rust staining. Documented plumbing configuration and compromised areas for repair recommendations.

Completed club single maintenance visit on HVAC system over 10 years old with indoor unit located in crawlspace. Performed standard maintenance inspection and conducted thorough ductwork evaluation as requested, examining flexible ductwork runs and interior plenum conditions. Inspected evaporator coil assembly showing normal dust accumulation consistent with system age, flexible duct insulation intact with proper support, and documented current system condition with photos. Installed 20x20x1 air filter and advised of routine maintenance recommendations for ductwork care.

Completed full residential HVAC system replacement including installation of RUUD 2.5 ton 15.2 SEER2 two-stage heat pump (model RP14AY30AJ2NA), RUUD 2.5 ton air handler (model RH2TY3617STANNJ), and RUUD 10kW electric heat kit (model RXBH-1724A10J-B). Installed new 3/8x3/4 refrigerant line set connecting outdoor condenser unit to indoor air handler. Mounted heat pump on rubber isolation pad against exterior foundation with proper clearances and secured electrical disconnect and conduit to exterior wall. Positioned air handler in crawl space with proper clearances and accessibility for future service. Installed new condensate drain line with safety switch to prevent overflow damage. Upgraded digital thermostat for improved temperature control and system operation. Performed ductwork modifications including insulating return plenum with foil duct wrap to prevent condensation and improve efficiency. Replaced one 6-inch supply run with new foil-faced R6 flex duct to eliminate air leakage

Responded to bathroom faucet leak in 1980s-era rental property. Upon inspection, traced leak source to deteriorated supply line connections in basement utility area. Identified corroded copper piping with significant oxidation and failing brass fittings at T-joint connections. Replaced compromised brass connectors and integrated new PEX supply line to existing copper infrastructure. Shut off main water supply via red-handled valves, removed damaged fittings, and installed new brass transition fittings to ensure proper connection integrity. Restored water service and tested all connections for leaks. Verified faucet operation and confirmed no active leaks in bathroom or basement area.

Completed comprehensive 60-point visual plumbing inspection per GB protocol without flush testing. Inspected under-sink plumbing including P-trap configuration, PVC drain assembly, basket strainer mechanism, and braided flexible supply lines, confirming proper connections and absence of visible leaks. Evaluated shower fixture assembly including gooseneck pipe, rainfall showerhead operation, and control valve functionality, verifying adequate water flow and spray pattern with no observable drips or deterioration.

Completed installation of new propane gas line for pool heater by tapping into existing 3/4-inch gas line, upsizing to 1-inch, and running approximately 30 feet of new pipe through exterior wall to customer-provided pool heater. Hard-piped gas connection to heater unit with 3/4-inch sediment trap and shut-off valve installed immediately upstream of appliance. Verified all connections for gas leaks prior to completion; no leaks detected on newly installed gas line system.

Completed final installation steps for HVAC system including installation of registers and grilles throughout the structure. Applied black spray paint to return air panning for finished appearance per customer specifications. Performed comprehensive system operation check, verified proper airflow and temperature readings using infrared thermometer, confirmed all components functioning correctly, and ensured installation ready for final inspection approval.

Responded to callback for system not operating properly following previous maintenance visit where adjustments were made. Inspected Goodman unit model CM48E3L-177L-000 and documented equipment condition with photos. System continues to exhibit same operational issues reported during initial service call, requiring further diagnostic evaluation to identify root cause.

Responded to no power condition affecting water heater. Located electrical disconnects in area accessible through bedroom closet. Replaced obsolete fused disconnect switch with new non-fused safety disconnect per current code requirements. Verified proper wire terminations, restored power to water heater circuit, and confirmed operational status of equipment upon completion.

Responded to no hot water complaint on recently installed tank water heater. Upon arrival, confirmed complete loss of hot water throughout residence for three days. Customer had previously attempted troubleshooting by checking and replacing fuses without resolution. Inspected electrical disconnect box serving water heater. Found two 18-amp and 30-amp fuse holders with brass bus bars and multiple wire connections. Observed accumulated debris and dust in bottom of enclosure. Tested electrical continuity and verified proper fuse sizing for water heater load requirements. Checked all wire connections at terminals for tightness and proper installation. Verified power supply to unit and tested heating elements for functionality. Restored hot water service to residence. Documented electrical panel condition with photographs for service records.

Completed whole-home plumbing fixture installation and trim-out work on existing rough-in plumbing. Installed homeowner-supplied fixtures including utility sink with gooseneck faucet in designated room. Performed system pressurization, leak testing at all connection points, and functional verification of all installed fixtures to ensure proper operation throughout the residence.

# HVAC Service Call - No Heat Condition Responded to a no heat service call for a 3-year-old electric heat pump system blowing room temperature air. Upon arrival, accessed the indoor air handler unit located near the back door and performed diagnostic evaluation of the heating system. Inspection revealed an issue with the control board requiring attention. Removed access panel to examine the circuit board assembly, which displayed part number 1006801REV-A. Documented the control board condition with photographs showing the PCB with multiple wire connections including blue, orange, yellow, and brown/black conductors properly terminated to the board. The circuit board appeared to be the source of the heating malfunction based on system behavior and diagnostic findings. Performed thorough evaluation of all electrical connections, wire terminations, and board components to identify the root cause of the no heat condition. The heat pump system was not engaging heating mode properly, resu

Successfully installed a WaterFurnace 3 Series Geothermal Package Unit (W3AV036BD1A01CTL0A10) with two-stage operation featuring 22.4 EER and 4.3 COP ratings. Completed installation included supplemental strip heat kit (EAL10B), flow pump center in crawl space (FC1-FPT), hose kit (CK4LI), fittings (MA4SWV), and Wi-Fi thermostat, while utilizing the existing return filter grille.

Completed warranty replacement of defective reversing valve on HVAC system. Verified proper operation after installation and documented equipment information with photographic evidence for warranty claim processing. System is now functioning correctly with all refrigerant lines properly connected.

Completed plumbing estimate for bathroom rough-in with two sets of hot/cold water supply lines protruding from the wall, marked with appropriate color indicators. Observed electrical work in progress with multiple outlet boxes installed and noted preparation for future fixture installations including two circular wall cutouts requiring coordination with electrical components.

Responded to service call for reported water leak in a 70-year-old residence. Inspected water meter (BadgerMeter Model 25) which showed active consumption despite fixtures being off, confirming presence of a leak. Examination of the foundation perimeter revealed moisture accumulation near landscaping at the house exterior, indicating underground supply line damage requiring further excavation and repair.

Successfully installed a complete HVAC system in an office space renovation, including a 3-ton 14 SEER2 Rheem/RUUD heat pump with R-454B refrigerant, 15kW auxiliary heat kit, and multi-positional air handler. System installation included comprehensive ductwork, safety components (overflow pan, water sensors), digital programmable thermostat, and venting for two customer-supplied bath fans.