Reliable Plumbing in Versailles, KY

Completed comprehensive Care Plan tune-up on air conditioning system with equipment located in crawlspace. Performed detailed inspection of all system components, measured electrical amperage readings using clamp meter to verify proper compressor and fan motor operation within manufacturer specifications, and documented system performance with photographic evidence. Customer-provided filter was installed per service agreement requirements.

Completed comprehensive Club Single maintenance tune-up on dual HVAC system (Unit #171, sides A and B) consisting of two air conditioning units and two gas furnaces. Performed thorough inspection of condensation drain lines as specifically requested, verified proper drainage and cleared any potential blockages. Conducted standard preventative maintenance procedures including system performance testing, temperature differential measurements using calibrated digital instruments, and visual inspection of attic-mounted equipment and reflective insulation barriers.

Completed comprehensive Care Plan maintenance on gas furnace and two air conditioning systems, all located in basement. Performed standard tune-up procedures including temperature differential measurements across supply and return ducts, verified system operation, and inspected insulation on ductwork. Customer provided filters for installation during service visit. All equipment operating within normal parameters upon completion of maintenance procedures.

Completed comprehensive Club Trio maintenance service on residential HVAC system including air handler and water heater. Performed full system inspection, filter replacement, coil cleaning, refrigerant level verification, electrical connection testing, and condensate drain line clearing on the air handler unit. Inspected water heater for proper operation, checked temperature and pressure relief valve, examined anode rod condition, and verified all connections and venting. All components found operating within manufacturer specifications with no immediate repairs needed. Documented equipment condition with photographs showing minor age-related corrosion on some metal piping components but overall system integrity remains sound. Customer's care plan maintenance now current for 2024.

Completed comprehensive care plan tune-up on heat pump and air handler system located in attic space. Performed standard maintenance procedures including inspection of all mechanical components, electrical connections, and refrigerant levels using digital diagnostic equipment. Cleaned washable filter per system requirements and cleared maintenance reminder from thermostat per customer preference. Inspected outdoor condensing unit, noting accumulated debris on mesh panels and general weathering from outdoor exposure. All ductwork insulation and connections inspected and found intact. System operating within normal parameters following maintenance completion. No coil cleaning products utilized during service per customer sensitivity requirements.

Responded to water leak on 2001 geothermal system that was still operational for heating and cooling. Performed diagnostic testing using manifold gauges to check system pressures and identify source of leak. Coordinated access with property contact and documented equipment conditions with photos of testing equipment and unit components in crawl space area.

Removed and disposed of existing toilet from residential bathroom. Installed new Kohler brand toilet with new wax ring and supply line. Verified proper function and confirmed no leaks upon completion.

Responded to no cooling complaint on electric air conditioning system. Performed diagnostic testing and measured supply air temperatures at floor registers using calibrated digital thermometer. Initial supply air reading measured 61°F at decorative floor vent, with return air temperature at 79.2°F, indicating approximately 18.2°F temperature differential. Secondary measurements confirmed supply air temperature of 72.6°F at additional register location. Temperature split falls below optimal 15-20°F range expected for properly functioning residential cooling system, suggesting potential refrigerant charge issues, airflow restrictions, or compressor performance concerns requiring further diagnostic evaluation.

Conducted comprehensive assessment of existing 50-gallon electric A.O. Smith ProMax water heater located in basement utility area. Inspected unit specifications, copper piping connections, electrical wiring configuration, and overall installation condition to provide accurate replacement estimate for tank-style water heater system.

Completed comprehensive Care Plan tune-up on dual heat pump/air handler system with units located in crawlspace and attic. Performed full preventive maintenance inspection on both systems, accessing equipment through restricted entry points requiring ladder. Inspected electrical control panels, verified proper operation of TURBO200XM capacitor, control board, and relay components. All wiring connections found secure with no signs of overheating or damage. Customer provided filters for installation as part of routine maintenance protocol.

Conducted comprehensive system evaluation for complete HVAC replacement on 8-year-old equipment due to air quality concerns and inability to clean existing ductwork. Inspected attic-mounted flexible ductwork installation and documented extensive duct system requiring full replacement along with heating and cooling equipment. Provided detailed assessment and replacement recommendations for both HVAC system and complete duct work replacement to address indoor air quality issues and system performance.

Completed electrical estimate for powering an Airstream trailer. Assessed existing twist-lock style power inlet receptacle mounted on the trailer's exterior aluminum panel and evaluated the yellow weatherproof connector outlet positioned at ground level near the unit. Determined electrical requirements and connection specifications for establishing proper 120/240V service to the recreational vehicle.

Completed comprehensive Care Plan tune-up service on dual-zone system including heat pump/gas furnace and mini-split units located in basement and office areas. Performed temperature diagnostics at supply vents, recording discharge air temperatures of 45.6°F in cooling mode to verify proper system operation and refrigerant charge levels. All equipment inspected and operating within manufacturer specifications.

Completed comprehensive Club Trio maintenance service on three-system property consisting of geothermal unit, secondary HVAC system, and mini-split unit located in barn area. Performed full tune-up procedures on geothermal system including temperature diagnostics measuring supply air at 43.5°F, pressure testing with gauge readings at operational levels, and visual inspection of copper refrigerant lines and connections. Conducted maintenance on mini-split system in basement barn location. Sanitized equipment surfaces using antibacterial wipes during service. All systems tested and operating within normal parameters upon completion.

Responded to no cooling condition on 7-year-old HVAC system displaying error codes 2, 5, and 7. Upon arrival, unit had been shut down due to multiple fault codes. Performed diagnostic testing using clamp meter to measure electrical parameters and verify system operation. Documented equipment readings and conditions for service record purposes.

Completed comprehensive maintenance service on Generac Guardian Series 17kW air-cooled standby generator, model G0062420, serial number 8375429. Performed thorough inspection of physical location, generator enclosure exterior and interior condition, and verified proper mounting on concrete pad. Conducted complete fuel system inspection and battery electrical testing to ensure reliable starting capability. Executed high and low voltage electrical connection testing at both the generator unit and transfer switch panel to verify proper power transfer functionality. Replaced spark plugs, air filter, and oil filter as part of routine maintenance schedule. Performed valve adjustment as needed to maintain optimal engine performance. Conducted comprehensive system verification testing in both manual and automatic modes under load conditions to confirm proper operation of all components including the transfer switch and circuit protection devices. All systems tested successfully and unit retur

Responded to callback for non-functioning thermostat on system installed 8 months prior. Upon arrival, confirmed thermostat had backlight power but displayed no information and was unresponsive to inputs, leaving HVAC system inoperable. Performed diagnostic testing using digital multimeter to verify 24VAC power supply to thermostat terminals. Determined thermostat had internal component failure preventing proper display and communication with system. Replaced defective thermostat with new unit, verified proper wiring connections at R, C, W, Y, and G terminals, and restored power to system. Confirmed new thermostat powered on correctly with full display functionality and responsive touch controls. Cycled system through heating and cooling modes to verify proper communication between thermostat and equipment. System now operating normally with full thermostat control restored.

Responded to emergency plumbing service call for active water leak in crawlspace that was causing excessive runtime on spring pump. Located source of dripping leak on copper piping in crawlspace area where heat tape had been previously installed during winter months. Accessed confined crawlspace area with exposed floor joists, concrete block foundation walls, and existing fiberglass insulation. Inspected copper pipe runs and identified leak at pipe coupling/connector joint. Removed deteriorated and water-damaged insulation material from affected area to access leak point. Repaired leaking copper pipe connection to stop active drip and prevent further water accumulation in crawlspace. Verified repair held pressure and leak was fully resolved to prevent continued strain on spring pump system.

Responded to callback for water leakage from newly installed mini-split system. Upon inspection, identified improper condensate drain line installation causing water to discharge at outdoor unit location rather than routing to appropriate drainage point. Corrected drain line pitch and secured proper drainage routing to resolve issue.

Completed routine preventive maintenance tune-up on heat pump and air handler system per care plan agreement. Performed comprehensive system diagnostics including electrical measurements in attic-mounted equipment, verified thermostat operation and programming on Honeywell Home ProSeries unit displaying proper temperature control at 71 degrees. Customer provided their own 16x25x4 filter for replacement during service visit.