Top-Rated Heating, Cooling in Lexington, KY

Completed Care Plan tune-up on a zoned air conditioning system with gas furnace located in basement. Inspected and serviced cylindrical air filter assembly, noting light dust accumulation on pleated filter media. Verified proper operation of Honeywell Home motorized damper control in ductwork, confirming dial indicators and electrical connections are functioning correctly. System operational with both zones responding appropriately to thermostat calls.

Completed full heat pump and air handler replacement at residential property. Removed existing equipment and installed Bryant 3.5 ton 14.3 SEER2 single stage heat pump system with matching air handler in walk-in attic, 15KW auxiliary heat kit, and Honeywell programmable digital thermostat. Installation included outdoor unit pad with snow legs, electrical disconnect box, electrical whip kit, insulated refrigerant lines with filter, trap, SS2 coil drain safety sensor, ceiling saver overflow drain pan with water sensor, transition to existing ductwork, and standard air filter rack. All permits obtained, electrical connections completed per code, system tested and operational, existing equipment removed and disposed of properly.

Responded to water leak complaint at indoor HVAC unit located in loft utility closet. Upon inspection, found severely clogged 20x20x1 air filter with heavy dust and debris accumulation restricting airflow. The restricted airflow caused evaporator coil to freeze, resulting in water dripping into bucket as ice melted. Replaced dirty filter with new unit, restored proper airflow to system, and verified no further water leakage occurring.

Completed routine maintenance service on a residential Generac standby generator unit installed approximately 1.5 years ago. Performed standard inspection procedures, verified proper operation of all components, and confirmed unit remains in good working condition with exhaust system properly vented along exterior wall.

Accessed ceiling cavity to remove and replace deteriorated galvanized water supply line. Cut opening in drywall ceiling to expose existing pipe run and structural framing. Removed old galvanized piping and installed new PEX water line through ceiling space, securing properly to structural members. Installed new hose bibb at designated location and pressure tested system to verify proper operation and confirm no leaks. All connections made to code specifications with appropriate fittings and support.

Responded to no-cooling complaint on 25-year-old split system where indoor air handler attempted to start but only produced humming noise without running. Upon inspection of under-house unit in crawl space, diagnosed failed compressor motor exhibiting locked rotor condition preventing normal startup operation. Due to age of equipment and cost of compressor replacement exceeding value of repair, recommended full system replacement and provided customer with options for new high-efficiency equipment installation.

Completed Care Plan tune-up service on Goodman air conditioning system. Accessed equipment through crawl space where customer-provided 16x20x4 Filterbuy filter was inspected and noted in place. Performed standard maintenance procedures on outdoor condensing unit located on concrete pad against exterior brick wall, verifying proper operation of all components. System operating within normal parameters upon completion of preventative maintenance visit.

Completed full residential HVAC system replacement with RUUD 2-ton two-stage heat pump (RP14AY24AJ2NA), 2-ton air handler (RH2TY2417STANNJ), and 10kW heat kit (RXBH-1724A10J-B). Installation included outdoor unit pad with snow legs, electrical disconnect box, electrical whip kit, insulated refrigerant lines with filter, digital thermostat, and standard air filter rack. Installed auxiliary drain pan in attic with water sensor, SS2 coil drain safety sensor, trap, and overflow drain pan with water sensor for ceiling protection. Created transition to existing ductwork and verified proper leveling of equipment. Removed and disposed of existing equipment, obtained applicable permits, and completed all work to code compliance standards. System startup performed with refrigerant charge verified and all safety controls tested for proper operation.

Responded to commercial no cooling call with reported water leakage causing ceiling tile damage. Accessed rooftop HVAC unit through tenant office suite and conducted thorough inspection of air handler and ductwork system. Upon examination, identified condensate drainage issues and inadequate duct insulation contributing to moisture intrusion. Documented water-stained ceiling tiles and inspected duct connections showing aged foil tape sealing. Photographed affected areas including damaged ceiling tiles with visible water rings and close-up views of ductwork assembly with worn tape sealing at connections. Verified roof had been previously inspected and ruled out as source of water intrusion. Findings indicate condensate management system requires attention and ductwork insulation needs replacement or supplementation to prevent continued moisture problems and restore proper system operation.

Completed comprehensive maintenance tune-up on dual HVAC system consisting of heat pump and air handler units located in basement and attic spaces. Performed thorough inspection and servicing of both systems, noting significant dust and debris accumulation within air handler compartment requiring attention during routine maintenance procedures. Customer provided filters for installation as part of preventative care plan service.

Responded to service call for 7-year-old geothermal system with reported annual refrigerant loss. Performed diagnostic pressure testing using analog gauges to assess system pressures and identify potential leak points in the refrigerant circuit. Customer reported uncertainty whether leak involved refrigerant or water loop, though system currently operating without performance degradation; further leak detection and monitoring recommended to determine source and prevent future recharge requirements.

Coordinated with energy solutions team on-site to complete duct blast testing for HVAC final inspection. Conducted comprehensive walk-through of entire system, verifying all components operational including thermostat controls, air distribution registers, and auxiliary heat functions. Confirmed installation meets code requirements, system running properly, and work area cleaned and prepared for final inspection approval.

Completed preventive maintenance tune-up on dual system care plan consisting of one gas furnace/AC unit located in attic and one unit in first floor closet. Performed comprehensive inspection and cleaning of both systems. Inspected evaporator coil which showed moderate dust and debris accumulation with heavier buildup in lower sections; cleaned coil surfaces to restore proper airflow and heat transfer efficiency. Serviced outdoor condenser unit with visible dirt and grime on exterior fins; cleaned condenser coils to ensure optimal heat rejection and system performance. Verified all mechanical and electrical components operating within normal parameters on both units. Customer provided 20x20x1 filters for installation as part of routine maintenance protocol.

Responded to a toilet malfunction caused by a broken float rod. Upon inspection, found the float rod had failed, preventing proper tank refilling and flush cycle operation. Removed the damaged float rod assembly and replaced it with a new unit. Tested the fill valve operation and adjusted water level to manufacturer specifications. Verified proper flapper seal and flush mechanism function. Cleaned mineral deposits from tank components to ensure optimal performance. Completed final testing to confirm proper fill, flush, and shutoff cycles.

Responded to no cooling call for residential property with multiple geothermal heat pump systems. Upon arrival, found customer operates 7 WaterFurnace Envision geothermal units throughout the home. Conducted systematic inspection of units, focusing on unit #5 and unit #7 as photographed during diagnostic process. Evaluated electrical connections, control boards, and thermostat operations on affected systems. Inspected wall-mounted controls showing indicator lights and verified proper communication between thermostats and air handlers. Checked Carrier-branded air handling components and associated ductwork for airflow restrictions. Reviewed service history notations marked on equipment cabinets dating back to previous maintenance visits. Assessed geothermal loop connections and blue buffer tanks attached to units. Determined which of the 7 geothermal systems were experiencing cooling failures versus operating normally. Documented equipment conditions with photographs for service records

Responded to service call for thermostat installation at customer's residence. Successfully removed existing thermostat and installed new Sensi digital Wi-Fi thermostat with programmable features and LCD display. Configured device settings, verified proper HVAC system communication, connected unit to Wi-Fi network, and confirmed heating and cooling functionality. Provided detailed verbal instructions on thermostat operation to ensure customers could independently adjust temperature settings and utilize voice control features through compatible smart home devices.

Responded to ongoing toilet leak in residential bathroom of 20+ year old home. Upon inspection, identified failed water supply line connection at fill valve with visible corrosion and seepage at floor-mounted shutoff valve. Replaced deteriorated braided supply line and corroded angle stop valve. Cleaned residual staining from tile flooring around connection point, tested system for proper operation and verified no additional leaks present.

Completed routine AC tune-up on a 9-year-old air conditioning system located in the basement. Performed comprehensive maintenance including electrical testing with multimeter, inspected condensate pump assembly, and verified all system components were operating within normal parameters. System checked and confirmed to be functioning properly.

Responded to no-cooling complaint on aging air conditioning system paired with 2-year-old Bryant gas furnace in basement location. Customer reported unit unable to maintain temperature below 75 degrees during warm weather over the past several days. Performed diagnostic evaluation of complete HVAC system including inspection of indoor air handler, refrigerant lines, ductwork connections, and electrical components. Documented equipment conditions with photographic evidence showing existing installation configuration, PVC condensate drainage system, flexible duct connections, and overall mechanical room layout for service records.

Completed full residential HVAC system installation including Bryant 3-ton 16 SEER2 air conditioning unit (model GA5SAN53602W) and matching Bryant 3-ton evaporator coil (model CVAVA3621XMA) with digital thermostat. Removed and disposed of existing equipment per code compliance requirements. Installed outdoor unit on concrete pad with electrical disconnect box, whip kit, and proper refrigerant line insulation. Mounted evaporator coil in air handler with transition to existing ductwork, installed refrigerant line filter drier, and SS2 coil drain safety water sensor. Secured all refrigerant lines, completed electrical connections, pulled necessary permits, pressure tested system, evacuated lines, charged unit to manufacturer specifications, and performed full operational testing to verify proper cooling performance and thermostat functionality.