Top-Rated Heating, Cooling in Lexington, KY

Responded to no cooling call on 15-year-old residential air conditioning system. Upon arrival, confirmed indoor blower motor operational but outdoor condenser unit fan not running. Performed diagnostic testing on outdoor unit using clamp meter, measuring electrical parameters at the condenser. Found outdoor fan motor failed with no amperage draw detected. Unit exhibited significant weathering, corrosion, and rust deterioration consistent with age and extended outdoor exposure. Due to the system's age exceeding typical equipment lifespan and the extent of deterioration observed, recommended full system replacement rather than repair. Discussed options with customer regarding continued operation and replacement considerations for aging equipment.

Completed Care Plan tune-up on air conditioning system and gas furnace unit located in basement. Performed comprehensive electrical diagnostics using clamp meter, measuring amp draws on blower motor and verifying proper system operation. All components tested and found operating within manufacturer specifications.

Responded to callback for heat pump installed four months prior experiencing intermittent AC operation with "no power" error after several minutes of runtime, followed by automatic system restoration. Inspected electrical connections, wiring, and control circuits for potential shorts or loose connections as reported. Measured temperature differentials and verified proper voltage supply to unit during troubleshooting process.

Responded to no cooling complaint on residential HVAC system over 10 years old. Upon arrival, located air handler unit in attic space and observed heavily soiled air filter with significant dust and debris accumulation restricting airflow. Inspected condensing unit at exterior window well location against foundation. System evaluation revealed compromised cooling performance directly related to restricted airflow from neglected filter maintenance, preventing adequate air circulation across evaporator coil and reducing system efficiency.

Responded to callback for unit not keeping up following April repair. Upon arrival, inspected electrical panel and circuit breakers to verify proper power supply to HVAC system. All breakers were found in correct positions with no tripped circuits. Documented electrical panel configuration for service records.

Conducted on-site assessment for installation of new primary sump pump system in basement utility area. Evaluated existing conditions including floor drain location, available electrical outlets, discharge piping configuration, and basin placement requirements. Customer will be supplying the pump unit for professional installation.

Removed existing 16KW standby generator and 100 AMP transfer switch from beneath deck structure. Installed new 18KW Generac air-cooled standby generator on prepared gravel pad with proper clearances for ventilation and service access. Mounted new 100 AMP non-service rated automatic transfer switch on exterior wall with appropriate conduit runs and emergency disconnect box. Verified all electrical connections, tested system operation through multiple transfer cycles, and confirmed proper generator startup and load transfer functionality.

Responded to water leak under kitchen sink. Upon inspection, identified leak occurring only when water drains from sink. Examined P-trap assembly, PVC drainage pipes, and garbage disposal connections for source of intermittent leak. Additionally replaced shower head with customer-supplied fixture per request.

Completed scheduled preventive maintenance tune-up on approximately 10-year-old air conditioning system located in crawlspace. Performed comprehensive electrical diagnostics using digital multimeter and clamp meter on outdoor condensing unit. Verified voltage readings at electrical panel, tested capacitor operation, and measured amperage draw showing 304.5 amps on compressor circuit. Inspected all wire connections including red, black, yellow, blue, green, and white conductors at terminal block. Confirmed proper electrical values and secure connections throughout system. Customer provided their own 16x25x4 air filter as specified. System operating within normal parameters upon completion of maintenance service.

Responded to reported water leak at 30-year-old residential property involving burst pipe connected to exterior hose bib. Upon inspection, identified failed compression fitting and damaged supply line running from outdoor spigot to interior plumbing system. Accessed under-sink cabinet area to assess extent of water damage and trace leak source to compromised pipe connection. Replaced faulty brass compression fittings, installed new flexible supply line, and secured all connections with appropriate fasteners. Verified outdoor hose bib mounting integrity and tested system for proper water flow and pressure. Confirmed no active leaks present after repairs and ensured all plumbing components functioning correctly.

Completed preventive maintenance tune-up on air conditioning and gas furnace system located in basement. Performed comprehensive system inspection, took temperature and performance readings using diagnostic equipment, and evaluated unit operation including condensate drainage system. Customer-supplied 16x25x1 filters were noted as part of the Care Plan service, with documentation that replacement filters are billable when provided by our company.

Completed routine plumbing inspection as part of preventative service agreement. Inspected under-sink plumbing connections, drain lines, and supply lines for leaks or deterioration, and examined toilet fixture including bidet attachment for proper operation and potential issues. All components found to be functioning properly with no immediate repairs required.

Completed full residential HVAC system replacement including removal and disposal of existing equipment. Installed RUUD 14.3 SEER2 two-stage 3-ton heat pump system (model RP14AY36AJ2NA) with matching two-stage air handler (model RH2TY3617STANNA) in attic location and 15KW auxiliary heat kit. Outdoor unit mounted on new pad with snow legs, electrical disconnect box, and whip kit installed per code requirements. Applied refrigerant line insulation and installed refrigerant line filter. Indoor installation included trap configuration, SS2 coil drain safety water sensor, and ceiling saver overflow drain pan with water sensor. Installed plywood support beneath auxiliary drain pan to ensure proper structural stability. Added transition to existing ductwork and standard-sized air filter rack. Upgraded to Honeywell programmable digital thermostat for improved system control. All work completed with applicable permits, tested for proper operation, and system verified to meet code compliance sta

Replaced outdoor condensing unit under manufacturer's 1-year warranty with new Lennox equipment. Installed surge protector for electrical protection and documented new unit's nameplate information with photographs for warranty claim processing.

Responded to no-cooling complaint on 17-year-old Carrier electric HVAC system located in utility room. Upon arrival, unit was off due to evaporator coil freeze-up occurring over previous several days. Performed diagnostic evaluation and confirmed suspected refrigerant leak. Documented system condition including deteriorated wooden structural support elements near installation area showing significant moisture damage and wood rot. Recommended system replacement due to age, refrigerant leak, and compromised installation integrity.

Responded to a slab leak in copper water line previously identified by leak detection services. Cut and removed interior flooring at marked location and used concrete saw and jackhammer to access the affected plumbing line beneath the slab. Located the leaking copper pipe, performed necessary repairs to restore water line integrity, and wrapped the repaired section for protection. Poured concrete to restore the slab foundation and verified proper system function with no additional leaks detected before completing the work.

Responded to clogged drain line affecting dishwasher operation. Upon inspection of the under-sink plumbing assembly, identified blockage in the drainage system connected to the dishwasher discharge line. Cleared obstruction from the drain line using appropriate methods, ensuring proper water flow through the P-trap assembly and main drainage piping. Verified all connections, including the black rubber dishwasher discharge hose secured with metal hose clamps to the white PVC drainage system, were properly seated and functioning. Tested system operation to confirm complete drainage and no leaks present at any connection points.

Responded to service call for air conditioning system not adequately cooling unoccupied residence. Upon arrival, verified thermostat set to 71°F in cooling mode and inspected HVAC equipment. Examined air handler unit and confirmed GeneralAire 16x25x5 MERV-rated filter was installed in system. System evaluated for cooling performance concerns reported by property caretaker.

Conducted comprehensive electrical assessment for generator installation at residential property. Evaluated existing electrical panel condition, noting deteriorated interior door panel requiring attention prior to generator integration. Documented current circuit breaker configuration and available capacity in main service panel to determine proper sizing and connection requirements for standby generator system. Assessed utility room electrical infrastructure and load requirements to ensure adequate power distribution for proposed automatic transfer switch installation.

Completed routine plumbing inspection as part of preventative service agreement. Verified proper water flow and drainage at bathroom sink fixture, tested faucet operation and water supply controls, and inspected accessible plumbing infrastructure in attic space for any visible leaks, proper insulation clearances, or maintenance concerns. All plumbing systems found operating within normal parameters with no immediate issues identified.