Top-Rated Heating, Cooling in Lexington, KY

Responded to non-urgent service call for water heater venting issue in basement. Upon inspection, confirmed water heater unit operating normally but discovered severe blockage and damage to roof vent termination. Accessed roof to assess vent condition and documented extensive fire or weather-related deterioration to metal vent stack, including charred surfaces, torn casing, and accumulated debris obstructing proper exhaust flow. Flashing around vent base showed signs of separation from roof surface. Advised customer that vent system requires complete replacement to restore safe venting operation and prevent potential carbon monoxide hazards. Recommended immediate attention to resolve blocked venting condition before continued water heater use.

Conducted comprehensive assessment of existing 80-gallon Bradford White tank-style water heater installed in basement mechanical room serving geothermal heating system. Evaluated current unit condition, plumbing connections including PEX supply lines with brass manifold assembly, shut-off valves, and flexible connectors. Documented installation configuration with copper and insulated piping at top connections, pressure relief valve assembly, and gas supply connections. Photographed equipment specifications, warning labels, and existing plumbing infrastructure to provide accurate replacement estimate and ensure proper sizing for geothermal system integration requirements.

Responded to under-sink leak at double basin kitchen sink. Upon inspection, identified leaking connections at both the rigid PVC drain piping and flexible supply lines. Tightened compression fittings, replaced deteriorated washers, and secured all connections at the shared P-trap assembly. Tested system under full water pressure and verified all leaks resolved.

Replaced the main circuit breaker in the electrical service panel and installed a new whole-home surge protection device to safeguard the residence from voltage spikes and power surges. Verified proper voltage readings of 244.5V using a digital clamp meter and ensured all circuit breaker connections were secure and functioning correctly within the panel box.

Responded to intermittent water leak reported in laundry room area. Upon investigation, identified roof penetration as the source, where a plumbing vent stack passes through the roofing surface. Inspected the flashing boot assembly and discovered deteriorated sealant around the pipe collar, with multiple areas showing weathering and compromised weatherproofing that would allow water infiltration during rain events. Applied fresh roofing cement to seal all compromised areas around the vent stack flashing and documented the repair with photographs for service records.

Completed annual preventive maintenance tune-up on heat pump system with air handler located in basement. Performed comprehensive system diagnostics including temperature differential measurements across coils registering 57.5°F and electrical current draw testing using clamp meter to verify proper compressor and fan motor operation. Installed billable 18x20x1 air filter as requested, inspected all electrical connections, and confirmed system operating within manufacturer specifications.

Completed comprehensive electrical estimate for full rewire of residential property currently under renovation. Assessed exposed framing in multiple areas including attic/crawl space and main living spaces where structure has been stripped to studs. Evaluated existing wiring conditions, documented cable routing through floor joists and wall cavities, and identified electrical device locations including mounted equipment between ceiling joists. Photographed current state of electrical infrastructure including visible white and dark-colored conductors running through open wall cavities. Provided detailed assessment for complete electrical system replacement including new circuit routing, device placement, and code-compliant installation throughout the gut-renovated space.

Responded to no cooling complaint on 3-year-old mini-split system experiencing freeze-up condition. Upon inspection, discovered severely clogged evaporator coil with heavy dust and debris accumulation restricting airflow, which was causing the coil to ice over and preventing proper heat exchange. Cleaned evaporator coil thoroughly, removed accumulated contaminants, and verified system operation. Recommended regular filter maintenance and periodic coil cleaning to prevent recurrence of airflow restriction issues.

# HVAC System Supply Plenum Rebuild and Component Replacement Completed comprehensive supply plenum reconstruction and system leveling for residential HVAC unit located in crawl space. The existing supply plenum connection to the evaporator coil required complete rebuild due to improper configuration and structural concerns. Fabricated new supply plenum using two sheets of sheet metal, ensuring proper dimensional specifications and airflow requirements. Installed new plenum with secure connections to evaporator coil, utilizing appropriate fasteners and sealing methods to prevent air leakage. Applied insulation wrap to newly constructed plenum to maintain thermal efficiency and prevent condensation issues. Assessed system installation and found unit improperly leveled, which can lead to drainage problems and premature component failure. Re-leveled entire HVAC unit using isolation pads to achieve proper pitch for condensate drainage and reduce operational vibration. Isolation pads ins

Responded to no cooling complaint on 1-year-old electric HVAC system with no airflow and green flashing light at outdoor unit. Upon inspection, found blower motor assembly failure preventing air circulation through the system. Diagnosed faulty blower motor and capacitor causing complete loss of indoor air movement while thermostat displayed 72°F actual temperature against 68°F setpoint. Accessed indoor unit compartment, disconnected electrical connections, and replaced defective blower motor assembly with OEM equivalent unit. Installed new run capacitor and verified proper wiring connections throughout blower circuit. Tested system operation, confirmed adequate airflow at all registers, and verified proper temperature differential across evaporator coil. System restored to full cooling capacity with normal operation confirmed.

Responded to service call for jammed garbage disposal causing both kitchen sinks to back up in 7-8 year old residence. Upon inspection, found 7-year-old disposal unit inoperable with standing water in both sink basins. Accessed unit from cabinet below, assessed mounting assembly and discharge connections. Cleared jam from disposal grinding chamber and verified proper motor function. Tested unit under load with water flow to ensure complete restoration of operation. Confirmed proper drainage through P-trap assembly and verified no leaks at disposal mounting flange or discharge elbow connection. Both kitchen sinks now draining properly with disposal functioning normally.

Responded to service call for non-operational air conditioning system with abnormal noise complaints on a three-year-old unit. Upon inspection, evaluated the existing outdoor condensing unit and indoor air handler system, documenting equipment condition and configuration. Provided comprehensive estimate for complete HVAC system replacement, presenting repair versus replacement options to address the equipment failure and operational concerns.

Responded to no-cool complaint on three-year-old air conditioning system. Upon arrival, accessed unit using provided entry code as homeowner was away. Diagnosed failed dual-run capacitor causing compressor and condenser fan motor failure, which also produced abnormal noise reported by customer. Tested capacitor with multimeter, confirming readings of 199 microfarads out of specification range. Replaced defective capacitor with new SuperCo unit, verified proper electrical connections, and tested system operation. Unit restored to normal cooling operation with compressor and fan motor running within manufacturer specifications.

Replaced evaporator coil under warranty on attic-mounted HVAC system. Previously reclaimed refrigerant was recycled back into the unit from clean storage tank to prevent further loss during repair. Documented new coil model and serial number information for warranty claim processing and retrieved loaner window units from property.

Completed plumbing inspection of basement crawl space to assess water line relocation needs and evaluate condition of existing piping system. Inspected water supply lines currently routed through wooden structural members requiring repositioning to meet code compliance and prevent future damage. Documented aging galvanized and steel pipes showing significant deterioration, corrosion, and discoloration throughout the system. Evaluated existing PVC drainage lines and mounting hardware for structural integrity. Assessed accessibility constraints within crawl space including exposed floor joists, concrete block foundation walls, and limited clearance areas. Photographed current pipe routing, support bracket locations, and areas requiring replacement to provide comprehensive documentation for estimate preparation and future repair work.

Completed tanked water heater installation including removal and proper disposal of existing unit. Temporarily shut off water supply to the home and installed new shut-off valves on top of the water heater. Modified PEX piping by cutting back connections to the wall to maintain proper clearance from the exhaust vent. Connected water supply lines, filled the tank completely, and ignited the burner assembly. Performed comprehensive leak inspection at all connection points and verified proper system functionality before completing the installation.

Responded to urgent no-cooling call for one-year-old Trane heat pump system. Inspected main electrical panel and distribution system in basement utility area to verify power supply to outdoor compressor unit. Documented electrical panel configuration and circuit breaker arrangement for whole-house HVAC system. Provided quote for surge protector installation to protect new heat pump equipment from electrical damage.

Performed comprehensive pre-purchase HVAC system inspection at property. Conducted visual assessment of air handler unit, noting absence of condensate overflow safety switch on equipment. Evaluated ductwork connections, flex duct installation, and associated plumbing components for proper installation and condition. Performed electrical diagnostics using clamp meter, recording amperage draw of 17.40 amps on system components. Inspected control board, relay components, and electrical connections within control panel for proper operation. Documented equipment condition, installation quality, and operational parameters with photos for buyer's records.

Responded to no cooling call on 4-year-old electric HVAC system with indoor temperature exceeding 80 degrees. Found Honeywell TH8321WF1001 thermostat display completely blank and non-responsive. Diagnosed low battery condition preventing thermostat operation. Replaced thermostat batteries, restored power to unit, and verified proper communication between thermostat and HVAC system. Confirmed system entered normal wait cycle and programmed schedule was intact with proper temperature setpoints. System returned to normal cooling operation with display showing current temperature, humidity readings, and all functions operational.

Responded to no cooling call on 12-year-old electric HVAC system. Upon arrival, found exterior electrical disconnect box had been accidentally pulled from brick wall with wiring damaged and disconnected. Reinstalled disconnect box securely to exterior wall, reconnected and properly terminated all electrical wiring including line voltage connections, verified proper polarity and grounding, and restored power to outdoor condensing unit. Tested system operation and confirmed unit returned to normal cooling function with all electrical connections secure and code-compliant.