Top-Rated Heating, Cooling in Lexington, KY

Completed routine care plan maintenance on air conditioning system with gas furnace located in first floor closet. Performed comprehensive tune-up inspection of both indoor and outdoor units. Verified electrical components including dual-run capacitor (45/5μF, 440VAC) and contactor relay, confirming all connections secure and within manufacturer specifications. Conducted electrical measurements at outdoor condensing unit using digital multimeter to verify proper voltage and amperage. Inspected all wiring terminations and found system operating normally. Customer provided 20x25x1 filter as specified. All components functioning properly with no issues identified during preventive maintenance visit.

Completed Gold Level annual maintenance on single-system residential HVAC unit. Performed comprehensive inspection of outdoor condensing unit and indoor blower assembly, including evaluation of blower wheel condition, motor shaft coupling, and overall system cleanliness. Unit found operating within normal parameters with components showing minimal wear and proper maintenance history.

Completed full HVAC system replacement installing Bryant 2-ton 14.3 SEER2 single-stage air conditioning unit (model GA5SAN52400W) with matching Bryant 2-ton evaporator coil (model CVAMA2417XMA) and condensate pump. Removed and properly disposed of existing equipment, then installed new outdoor condensing unit on existing pad utilizing existing disconnect box. Fabricated and installed new supply and return plenums, ran 6-inch supply ductwork, hung and sealed existing supply runs, and added additional floor return at customer-specified location per custom ductwork modifications. Connected refrigerant lines with copper piping, performed vacuum test, and charged system with R454B refrigerant to manufacturer specifications. Verified system operation with digital manifold gauges confirming proper superheat and subcooling temperatures, with readings showing system operating within normal parameters. Retained existing thermostat and integrated with new equipment. Obtained all applicable permit

Responded to water leak complaint at main floor bathroom sink. Upon arrival, inspected geometric basin sink with wall-mounted chrome faucet assembly and documented conditions with photographs. Customer reported leak occurs only when water is running, requiring bucket placement to catch water. Examined drain assembly from below, inspecting chrome P-trap, black plastic tailpiece, threaded couplings, and wall-mounted shut-off valves for hot and cold water supply lines. Assessed all visible plumbing connections, drainage system components, and fixture mounting points to identify source of active leak during water flow.

Completed preventive maintenance tune-up on two HVAC systems as part of Care Plan service. Both heat pump air handler units were accessed in their respective closet locations and thoroughly inspected. Performed standard maintenance procedures including cleaning of blower wheel assemblies, which showed moderate dust and debris accumulation on fan blades. Verified proper operation of both Trane air handler units, inspected refrigerant line connections, checked condensate drainage systems, and confirmed all manufacturer labels and safety warnings were intact. Customer to provide their own filters for both units.

Completed comprehensive Care Plan tune-up on heat pump and air handler system located in basement mechanical room. Performed thorough inspection of equipment including blower assembly, verified proper operation of all components, and documented system condition with detailed photographs. Customer will provide their own air filter for the unit.

Replaced failed evaporator coil located in attic with new unit. Evacuated system to proper vacuum levels as verified by digital vacuum gauge, then recharged system with 7 pounds of refrigerant to manufacturer specifications. Work was scheduled for early morning hours due to extreme attic temperatures, and additional assistance was utilized during the first hour to facilitate safe coil installation in the confined attic space.

Responded to callback for intermittent cooling issue that was previously investigated without resolution. Upon arrival, inspected electrical panel and circuit breakers supplying power to HVAC system, documenting conditions with photographs. System reportedly cycles on and off unpredictably, working properly for periods before ceasing operation for approximately one day, then resuming normal function without intervention, indicating potential electrical supply issue, faulty control board, or intermittent sensor failure requiring further diagnostic monitoring.

Completed dryer vent cleaning service at residential property. Removed significant accumulation of lint, debris, and moisture-laden material from the vent system, filling approximately half of a collection bucket with extracted buildup. Cleared exterior vent termination point at foundation level to restore proper airflow and prevent potential fire hazard and moisture issues.

Responded to a no-cooling complaint on a 4-year-old Rheem heat pump system that was originally installed by our company. Performed comprehensive diagnostic evaluation to provide second opinion after previous contractor recommended compressor replacement. Inspected outdoor condensing unit, verified electrical connections, and examined compressor operation and mechanical components. System evaluated and findings discussed with property owner regarding equipment condition and recommended course of action.

Performed comprehensive spring AC tune-up on 2-year-old air conditioning system with reported condensation issues on ductwork. Inspected condensate drain line and PVC piping connections in crawl space, verifying proper drainage and checking for leaks or blockages that could cause moisture accumulation. Measured system performance parameters including temperature differential across evaporator coil, which registered 43.74 degrees, indicating adequate cooling capacity and refrigerant charge. Examined all accessible ductwork for condensation, insulation integrity, and proper sealing. Cleaned and inspected 7-year-old washable filters located in garage. Checked refrigerant lines, electrical connections, and mechanical components for proper operation. System operating within normal parameters with no immediate concerns identified.

Responded to report of grinding noise from 5-year-old air conditioning unit located in crawl space. Upon inspection, discovered severely clogged air return filter and blower wheel assembly heavily coated with dust and debris accumulation. Identified excessive dust buildup on blower wheel blades and housing as primary cause of grinding noise and restricted airflow. Cleaned blower assembly, replaced air filter, and verified proper system operation. Unit returned to normal operation with no abnormal sounds detected. Recommended regular filter maintenance to prevent future issues.

Responded to basement flooding incident affecting HVAC system. Performed comprehensive safety inspection of furnace unit that had been submerged and powered off as precautionary measure. Conducted visual assessment of equipment interior, checking for water damage, contamination, and potential mold growth. Measured internal temperature at 53.9°F and inspected reflective duct insulation for water intrusion and structural integrity. Documented water line marks approximately 14 inches high on insulation material, indicating flood depth. Evaluated foil-faced insulation for signs of moisture retention, degradation, and microbial growth concerns. Inspected electrical components, wiring, and connections for water exposure and corrosion. Unit remains de-energized pending further assessment and drying period. Recommend professional water damage remediation, thorough drying of all components, and follow-up inspection before restoration of service to ensure safe operation.

Completed comprehensive Care Plan maintenance on dual HVAC system including two air conditioning units and two gas furnaces. Performed tune-up procedures on all four units, replaced air filters per plan coverage specifications (two 20x25x1 filters and one 16x25x2 filter for downstairs unit), and conducted full system diagnostics using calibrated measurement instruments. Inspected Bryant furnace installation, verified proper operation of condensate pump and drainage systems, checked all PVC venting and condensate lines for proper connections, confirmed gas line integrity, and assessed ductwork insulation. All systems operating within manufacturer specifications with no deficiencies noted.

Performed ultrasonic leak search on HVAC system with specific focus on lineset as suspected leak source. Upon inspection, evaporator coil showed significant contamination with dust accumulation, discoloration, and localized frost/ice buildup indicating active refrigerant leak and compromised heat transfer efficiency. Documented coil condition showing uneven frost patterns and debris accumulation on fins, confirming need for leak repair and system servicing.

Responded to downstairs HVAC system with reported condensate line blockage and overflow condition. Upon arrival, inspected older heating system unit and verified condensate drain pan was near capacity. Cleared clogged condensate drain line using appropriate tools and techniques to restore proper drainage flow. Verified system operation and confirmed condensate is now draining properly with no further overflow risk.

Responded to warranty call for dual-zone system with downstairs thermostat displaying blank screen and upstairs unit not cooling properly. Upon inspection, discovered severely damaged low-voltage wiring with burned and melted insulation exposing conductors, indicating electrical failure or short circuit. Replaced damaged thermostat wiring to restore communication between system components and thermostat operation.

Responded to no cooling complaint on 3-year-old electric air conditioning system with indoor temperature at 78 degrees. Upon inspection, discovered blower motor issue following recent maintenance tune-up performed previous week. Diagnosed faulty blower motor assembly, verified electrical connections and capacitor functionality, and replaced defective 1/2 HP blower motor with OEM equivalent unit. Tested system operation, confirmed proper airflow restoration, and verified cooling cycle functionality with all safety controls operating within manufacturer specifications.

Replaced defective smoke detector in commercial HVAC system control panel. Verified proper wiring connections to terminal blocks and tested alarm functionality to ensure system safety compliance.

Responded to no hot water complaint on 6-year-old residential gas water heater. Upon arrival, confirmed pilot light was extinguished, likely due to recent storm activity. Inspected gas control valve, thermocouple, and burner assembly for proper operation. Successfully relit pilot light following manufacturer specifications and verified stable flame. Tested gas control valve functionality and confirmed proper temperature settings. Checked pressure relief valve, supply lines, and all plumbing connections for leaks or damage. Verified adequate combustion air supply and proper venting. Unit restored to full operation with hot water production confirmed before departure.