Top-Rated Heating, Cooling in Lexington, KY

Responded to no cooling complaint on commercial HVAC system with Honeywell Pro Series thermostat showing 8-degree temperature differential. Upon inspection, identified severely restricted airflow due to clogged air filters. Removed and replaced four dirty filters with new KOCH brand pleated filters. Verified proper system operation, confirmed adequate airflow restoration, and tested thermostat functionality to ensure unit achieved setpoint temperature.

Completed plumbing estimate for commercial water heater replacement in utility closet. Assessed existing 75-gallon gas-fired Bradford White tank water heater with standard venting and copper supply lines. Documented current installation including top-mounted flue vent, dual shut-off valves with blue handles, gas control valve assembly, and proper grounding connections for replacement specifications.

Responded to a broken drain pipe emergency in a bedroom wall where the homeowner had already exposed the damaged section. Upon inspection, found a cracked 3-inch PVC drain pipe at the T-junction where a smaller branch line diverted, with water supply already shut off. Removed the damaged section of pipe and T-fitting, then installed new PVC components to restore proper drainage function. Tested the repaired drain system for leaks and proper flow before completing the work.

Completed USA Gold Duo Annual preventive maintenance on dual-zone HVAC system consisting of two heat pump and air handler combinations installed in attic space. Performed comprehensive inspection and maintenance procedures on both units including filter evaluation, electrical connection verification, condensate drain line inspection, and system operational testing. All equipment found operating within manufacturer specifications with no deficiencies noted. Both air handlers properly secured on wooden platforms with adequate clearance for service access. Documented system conditions with photographic records showing unit installations, ductwork configurations, and proper labeling of equipment.

Completed Gold Level annual preventive maintenance on single-system HVAC unit located in basement. Performed electrical diagnostics on air handler, measuring current draw at 68.2 amps using clamp meter to verify proper compressor and blower motor operation. Verified wall-mounted thermostat functionality and system response. Customer providing their own filters as requested.

Completed preventive maintenance filter change service on four commercial HVAC units as part of Club Trio maintenance agreement. Replaced two 20x20x1 filters on units located in warehouse closet serving front offices and two 18x20x1 filters on warehouse-mounted units requiring ladder access. Inspected electrical components including capacitor and contactor assembly, verified proper wire connections, and documented equipment condition with photographs per customer requirements.

Completed full bathtub and shower installation featuring a 30x60 white left-hand tub unit with integrated surround. Removed existing tile and knockdown walls, installed new knockdown wall system, and fitted Delta chrome body faucets, shower valves, and tub spout. Installed Watco waste and overflow assembly, completed all water supply and drain connections, and performed final cleanup of work areas upon completion.

Completed comprehensive Club Trio maintenance on multi-zone HVAC system including one geothermal unit, two geothermal split systems, two gas furnaces, one heat pump with air handler serving apartment over garage, and two ERVs. Replaced all air filters per plan specifications (20x25x4, 30x36x2, 14x20x1), performed standard maintenance checks on all equipment, verified IntelliZone 2 thermostat operation, and documented system conditions with photos. All UV bulbs noted for replacement schedule per customer request during fall maintenance visits on two-year rotation.

Replaced existing chrome faucet with customer-supplied unit on commercial hand-washing sink located behind bar area. Disconnected old dual-handle faucet assembly, removed mounting hardware, and installed new faucet per manufacturer specifications. Verified water supply connections and tested for proper operation and leak-free performance upon completion.

Completed annual Gold Level preventative maintenance on single-system HVAC unit. Performed comprehensive electrical diagnostics including capacitor testing with digital multimeter, verifying proper microfarad readings and voltage levels at 182V. Measured amperage draw at 8.48 amps using clamp meter to confirm system operating within manufacturer specifications. All electrical components tested and found functioning properly with no deficiencies noted.

Completed preventative maintenance tune-up on heat pump air handler system located in kitchen closet. Performed comprehensive inspection of blower assembly, noting minor corrosion on motor shaft but confirmed proper operation and airflow. Measured supply air temperature at 28.85°F, indicating system is operating within normal cooling parameters. Inspected ductwork insulation and verified proper sealing of supply plenum connections. All components functioning as designed with no immediate service needs identified.

Responded to electrical estimate request for garage outlet replacement. Assessed damaged white electrical outlet that was overheating and structurally compromised, unable to securely retain plugs. Documented existing conditions showing outlet with multiple cords connected, located in garage utility area near floor-level plumbing. Provided estimate for replacement with new white outlet to restore safe electrical functionality.

Responded to service call for multiple plumbing issues including clogged guest bathroom drain, which was successfully cleared using drain snake equipment. Installed two customer-supplied garbage disposals at bar sink and kitchen sink locations, ensuring proper mounting, electrical connections, and drain line connections with leak testing performed. Inspected all water shut-off valves throughout the property for proper operation and functionality, noting existing brass angle stop valves with compression fittings showing age-related tarnishing but maintaining adequate service. Recommended installation of safety drain pan under water heater to prevent potential water damage from future leaks.

Responded to on-call service for Lennox furnace system. Diagnosed faulty control board and successfully replaced unit with OEM component. System tested and verified operational upon completion. Documented model and serial numbers for furnace, air conditioning unit, and evaporator coil as required for warranty and service records.

Completed warranty compressor replacement on Lennox unit. Removed failed compressor, installed new warranty replacement unit, and properly connected refrigerant lines with new filter drier. Captured and uploaded required photographs of both old and new compressor serial tags for warranty claim documentation as specified.

Performed preventative maintenance flush on tankless water heater unit. Isolated unit from water supply, connected descaling pump system with circulation hoses, and ran descaling solution through the heat exchanger to remove mineral buildup and maintain optimal efficiency. System was thoroughly flushed with clean water following the descaling process to remove all cleaning solution residue. Unit was returned to normal operation and tested for proper functionality.

Completed preventive maintenance tune-up on two HVAC systems (AC and gas furnace) located in attic space. Performed comprehensive inspection and testing of both units, verified proper airflow and temperature differentials using calibrated digital thermometer, and assessed overall system performance. Noted filter requirements for four filters: 10x10x1 and 20x20x1 sizes available for supply if requested by customer.

Completed scheduled maintenance on 24KW Generac EVO generator system. Performed standard inspection procedures, verified electrical connections at transfer switch panel and generator unit, and documented installation with required photographs of exterior electrical panel and generator location. All components found operational and properly secured.

Completed comprehensive kitchen sink plumbing upgrade including replacement of existing drain trap and discharge assembly with new PVC piping in proper P-trap configuration while maintaining existing garbage disposal unit. Removed old water supply lines and installed new copper supply piping with soldered connections and new shutoff valves for both hot and cold water lines. Successfully installed customer-supplied brushed nickel pull-down kitchen faucet with high arched spout on double-basin stainless steel sink. All connections tested and verified leak-free, with proper water flow and drainage confirmed upon completion.

Responded to kitchen faucet replacement request where customer had previously ordered and received a Delta faucet unit. Successfully removed existing faulty faucet assembly and installed the customer-supplied Delta replacement unit, ensuring proper connection of water supply lines and testing for leaks upon completion.