Top-Rated Heating, Cooling in Lexington, KY

Responded to no heat complaint on 12-year-old gas furnace system with uneven heating in two rooms. Upon arrival, inspected Honeywell thermostat showing 71°F indoor temperature with system set to cooling mode at 60°F. Proceeded to outdoor condensing unit to perform electrical diagnostics on air conditioning system as requested. Measured voltage at capacitor terminals using multimeter, recording 113V at the component. Inspected electrical connections including multiple wire terminations at capacitor and reviewed system specifications on equipment panel. Evaluated ductwork concerns related to uneven heat distribution in affected rooms and assessed overall system operation for both heating and cooling functions.

Responded to a toilet callback to address water drips in the basement drainage system. Replaced a defective section of drain pipe and associated fittings, including installation of a new toilet flange to eliminate leaks at the connection point. Completed drainage system repairs to restore proper function and prevent further water intrusion in the basement area.

Responded to no cooling call on 9-year-old downstairs AC unit where fan was running but no cold air was being produced. Upon inspection, found severely clogged air filter restricting airflow to the system. Replaced dirty filter with new one, restoring proper airflow and cooling operation to the unit.

Completed comprehensive Care Plan tune-up on geothermal system consisting of three ground-source heat pump units, one geothermal split system, air handler, and two humidifiers. Performed thorough inspection of ductwork components in attic space, verifying proper connections and airflow pathways. Conducted diagnostic measurements using digital testing equipment to assess system performance parameters and confirm optimal operating conditions across all equipment.

Performed comprehensive HVAC maintenance tune-up on a two-year-old residential cooling system as part of membership service. Completed full system inspection of outdoor condenser unit, including cleaning of coils, checking refrigerant lines and connections, and verifying proper operation of all components. Equipment type and model information was documented and forwarded to office for record updates.

Completed Gold Level prepaid maintenance service on dual HVAC system. Performed comprehensive inspection of both units, including filter examination and system diagnostics using digital testing equipment. Verified proper ductwork connections and sealing integrity on flexible duct runs, confirmed secure foil tape application at connection points. Documented equipment conditions with photographic evidence showing filter status and system measurements for maintenance records.

Responded to callback for recently installed toilet that was running continuously with intermittent bowl water loss. Upon inspection, identified faulty Fluidmaster fill valve assembly causing constant refill cycles. Removed defective red fill valve unit and replaced with new assembly, ensuring proper mounting and secure connections to water supply line. Adjusted float mechanism and verified proper shutoff operation. Tested system through multiple flush cycles to confirm bowl maintains proper water level and fill valve shuts off completely without continuous running.

Responded to no-cooling complaint on 15-year-old upstairs electric air conditioning system maintaining 4 degrees above setpoint. Accessed attic-mounted air handler unit for diagnostic evaluation. Performed system inspection including airflow assessment, refrigerant charge verification, and component operational testing. Evaluated air handler, ductwork connections, and condensate drainage system. Inspected flexible duct runs and supply plenum connections for proper sealing and airflow distribution. Checked electrical connections, capacitor function, and blower motor operation. Assessed insulation levels and attic conditions affecting system performance. Provided customer with findings and recommended solutions to restore proper cooling capacity and temperature control for aging system.

Completed full residential HVAC system installation including Bryant 2.5 ton 14.3 SEER2 heat pump (model GH5SAN53000A), Bryant air handler (model FJ5ANXB36L00) installed in attic space, and Bryant 10 KW heat kit (model TU-EC-10BKB). Positioned outdoor condenser unit on mounting pad with snow legs adjacent to home foundation, installed electrical disconnect box and whip kit with conduit run up exterior wall. Mounted air handler in attic with proper platform support over insulation, connected flexible ductwork to existing distribution system, and installed PVC condensate drain line with trap. Integrated existing thermostat with new system, installed insulated refrigerant lines between outdoor and indoor units, and added refrigerant line filter. Completed all electrical connections to code, obtained necessary permits, pressure tested refrigerant system, evacuated lines, charged system to manufacturer specifications, and verified proper operation of heating and cooling modes. Removed and d

Responded to service call regarding chemical odor in bedroom during air conditioning operation. Upon inspection, discovered condensate pump in crawl space with standing water accumulation on concrete floor, indicating drainage issues. Examined exterior drainage system and downspout configuration at foundation level. Chemical smell determined to be related to stagnant water in condensate system causing biological growth and odor transmission through HVAC ductwork. Documented moisture conditions and drainage components for recommended corrective action.

Responded to a no cooling complaint for a second opinion on a Trane XE 1000 split system previously diagnosed with compressor failure. Performed comprehensive diagnostic evaluation of the outdoor condensing unit, testing compressor electrical integrity including ohm readings for potential shorts or grounds to verify compressor condition. Inspected and tested run capacitor, contactor, and associated electrical components to rule out alternative failure causes. Confirmed compressor failure diagnosis and evaluated system age, refrigerant type, and overall equipment condition. Provided professional assessment regarding repair versus replacement options, taking into account the system's advanced age and cost-effectiveness of compressor replacement on legacy equipment. Documented indoor air handler condition and system configuration. Customer advised of findings and recommendations for next steps.

Completed comprehensive maintenance tune-up on geothermal HVAC system with humidifier located in basement. Performed thorough electrical diagnostics using clamp meter, verifying amperage draw at 102.5 amps and inspecting all control board connections and wiring harnesses to ensure proper operation. Measured system pressures using calibration gauges at brass valve manifold to confirm refrigerant charge and loop performance within manufacturer specifications. Verified all electrical connections were secure and properly seated, with special attention to ensuring no components were left disconnected. Customer provided replacement air filters and humidifier pad as requested for seasonal maintenance protocol.

Completed full residential HVAC system installation including Lennox ML180UH070E36AK 80% efficiency 66,000 BTU gas furnace, Lennox ML14KC1-030-230 2.5 ton 15.5 SEER2 air conditioning unit, and Lennox CK40HT-24A-71 evaporator coil. Removed and disposed of existing equipment, installed outdoor unit pad, electrical whip kit, electrical disconnect box, refrigerant line insulation, and refrigerant line filter drier. Fabricated and installed small strip of plywood and metal in front of furnace for rollout safety compliance. Completed transition from evaporator coil to existing ductwork, integrated existing thermostat with new system, and installed SS2 coil drain safety water sensor. Obtained applicable permits, tested all system operations, and verified proper function of all components.

Completed semi-annual maintenance on geothermal split system with ground-source heat pump, air handler located in attic/basement configuration. Performed comprehensive tune-up including electrical diagnostics with clamp meter readings, verified amperage draw at 5.59 amps on measured circuit, and inspected all accessible components. Evaluated outdoor condenser unit condition, checked proper elevation on support blocks, and confirmed adequate clearance around unit for airflow; customer provides their own filters for this system.

Completed scheduled filter change in basement mechanical room using customer-supplied filters. Accessed HVAC system through exterior deck hatch and performed filter replacement on furnace unit. Provided written quote for complete furnace replacement as requested.

Responded to kitchen sink backup issue caused by inadequate drainage through existing flexible drain lines. Assessed under-sink plumbing configuration and identified ribbed flex tubing as primary concern for recurring clogs. Provided estimate to replace multiple sink drain assemblies, converting from flexible corrugated pipe to rigid PVC drainage system for improved flow and long-term reliability. Documented existing P-trap configuration and connection points for garbage disposal line to ensure proper replacement specifications.

Responded to service call for Generac backup generator displaying red warning light on control panel. Performed diagnostic inspection of unit mounted on exterior concrete pad, checked system status indicators, and reviewed fault codes. Determined cause of warning light, cleared alert condition, and verified generator returned to normal standby operation with all indicator lights showing proper status.

Completed routine maintenance on four air conditioning systems during morning appointment. Performed comprehensive AC tune-ups on all units, including two wall-mounted systems observed in upper-level spaces with wooden surrounds and vintage Emerson Quiet Kool equipment. Replaced air filters as specified: two 20x20x4 filters, one 16x25x4 filter, and cleaned one washable filter. Utilized 12-foot ladder to access elevated units. Inspected all system components, verified proper operation of controls and louvers, and confirmed adequate airflow through discharge vents. All systems operating within normal parameters upon completion of maintenance procedures.

Completed comprehensive 60-point plumbing inspection of residential property and performed water heater flush on Lochinvar tanked unit. All plumbing fixtures, connections, and systems were evaluated for proper operation, leaks, and code compliance, with the water heater receiving sediment removal service to maintain efficiency and extend equipment lifespan.

Completed comprehensive spring AC tune-up on dual heat pump/gas furnace system with units located in basement and attic. Performed electrical diagnostics using clamp meter to verify proper amperage draw on both systems, confirming compressor and blower motor performance within manufacturer specifications. Customer-supplied filters were installed, and all system components were inspected and tested to ensure optimal operation for the cooling season.