Top-Rated Heating, Cooling in Lexington, KY

Completed comprehensive Care Plan tune-up on dual-system HVAC configuration consisting of two heat pumps, two air handlers, and one humidifier. Performed standard maintenance protocols including temperature differential measurements at supply registers, recording 59°F discharge temperature. Conducted electrical diagnostics on outdoor heat pump unit, measuring 27.4 amp draw on compressor circuit to verify proper operation within manufacturer specifications. Inspected refrigerant line insulation, electrical connections, and overall system components for proper operation. Customer-supplied Aprilaire #313 humidifier filter noted for replacement during service. Both systems operating within normal parameters upon completion of maintenance procedures.

Responded to service call for kitchen remodeling project where removal of island platform exposed existing HVAC ductwork beneath floor. Upon arrival, inspected exposed floor cavity and identified flexible metallic supply duct running between floor joists along with PVC drain lines. Assessed ductwork condition and routing to determine if system was active and functional. Documented existing duct configuration with photographs showing duct suspended by straps in crawlspace area with accumulated debris present. Consulted with installer regarding original equipment layout and provided recommendations to customer on options for either removing non-functional ductwork or rerouting active supply lines to accommodate kitchen renovation plans.

Responded to no cooling call on 7-year-old Trane XR heat pump system (Model 4TWR4036G1000AA). Upon arrival, confirmed outdoor unit was not energizing and condenser fan was inoperative. Performed diagnostic testing and identified failed contactor preventing compressor and fan operation. Replaced defective contactor, restored power to outdoor unit, and verified proper system operation. Condenser fan and compressor now cycling correctly with adequate airflow and proper refrigerant pressures across the system.

Replaced defective compressor under warranty along with wire harness and filter drier to restore system functionality. Evacuated and recharged system with 14 pounds of refrigerant, verified proper operation, and confirmed supply air temperature of 62.8°F and return air temperature of 72.0°F upon completion.

Completed full HVAC system replacement in residential basement, installing RUUD R801T0503A14UHSNAS 50,000 BTU 80% efficiency gas furnace, RA14AY30AJ1NALHP 2.5 ton 14.3 SEER2 air conditioning unit, and RCFY3617STANMC 2.5 ton evaporator coil. Removed existing equipment and properly disposed of old system components. Set new furnace on ground level using isolation pads, removing previous blocking. Centered evaporator coil on furnace and fabricated custom sheet metal blocking for side gaps to ensure proper fit and airflow. Installed outdoor condensing unit on new equipment pad with electrical whip kit and disconnect box for code compliance. Ran and insulated refrigerant lines between indoor and outdoor units, installing filter drier in refrigerant circuit. Fabricated transition ductwork connecting evaporator coil to existing duct system using insulated metallic ductwork. Installed SS2 condensate safety switch with water sensor on drain line as secondary overflow protection. Connected con

Completed preventative maintenance tune-up on two HVAC systems as part of Club Duo care plan, with one unit located in attic and one in crawlspace. Performed comprehensive inspection and diagnostics on outdoor condensing units, including electrical testing with clamp meter to verify proper amperage draw and system performance. Customer provided two 16x25x4 filters for installation during service. All equipment tested and operating within normal parameters upon completion.

Completed comprehensive AC tune-up on 9-year-old cooling system. System operating properly upon arrival with customer reporting malodor from supply vents during operation. Performed standard maintenance protocol including filter inspection, refrigerant level verification, electrical connection testing, condensate drain evaluation, and airflow assessment. Inspected accessible ductwork and plumbing infrastructure in utility areas. Documented deteriorated pipe insulation, corroded PVC drainage components with visible rust staining at penetration points, and compromised condensate line conditions contributing to odor complaints. Identified moisture intrusion evidence on structural elements and accumulated debris in drain pan area affecting air quality. Recommended immediate attention to condensate drainage system repairs, duct cleaning services, and replacement of degraded pipe insulation to eliminate odor source and prevent further system contamination. System left in operational condi

Completed annual care plan tune-up on residential heat pump system as part of first-year complimentary maintenance included with new installation. Performed comprehensive system diagnostics using calibrated digital manifold gauges and Fieldpiece meter, recording operating temperatures and pressures to verify proper refrigerant charge and system performance. Inspected outdoor condenser unit for proper operation, confirmed fan motor function, checked electrical connections at disconnect panel, and documented system readings showing satisfactory cooling performance with measured temperatures and superheat/subcooling values within manufacturer specifications.

Completed preventive maintenance tune-up on residential air conditioning system and gas furnace located in basement per care plan agreement. Performed comprehensive electrical diagnostics using clamp meter, verifying amperage draws and voltage readings on both units to ensure proper operation within manufacturer specifications. All electrical connections inspected and found secure, refrigerant lines checked for proper insulation and routing, and system controls tested for functionality. Unit operating efficiently with all measurements within normal parameters.

Responded to a recurring bathtub clog that had not been fully resolved by previous snaking attempts. Accessed the crawl space beneath the residence to inspect the drainage system and replaced deteriorated PVC piping sections. Installed new white PVC pipe assembly with proper joints, elbows, and secure metal strapping brackets to the floor joists to ensure proper drainage flow and prevent future blockages.

Completed routine AC tune-up on a 10-year-old cooling system located in the basement. Performed comprehensive maintenance including electrical diagnostics using digital multimeter to verify proper voltage and amperage readings at the capacitor and contactor assembly, inspected and cleaned washable filters, and tested all electrical connections and components to ensure safe and efficient operation for the cooling season.

Completed Gold Level prepaid maintenance on single-system heat pump with air handler located in closet. Performed comprehensive system diagnostics including airflow measurements at floor register showing 46.1 CFM and electrical current draw testing at outdoor unit reading 0.6 AAC using clamp meter. Inspected all electrical connections, capacitor, and wiring at condensing unit, verified proper operation of all components, and documented system performance with photos per maintenance protocol.

Completed annual air conditioning maintenance and tune-up for Care Plan member. Performed comprehensive system diagnostics including electrical testing with clamp meter to verify proper amperage draw and voltage levels. Inspected blower wheel assembly and housing, noting normal dust accumulation on fan blades consistent with seasonal operation. All electrical connections tested within manufacturer specifications, and blower motor operation verified for proper performance. System operating efficiently with no deficiencies requiring immediate attention.

Completed comprehensive Care Plan tune-up on heat pump and air handler system located in attic space. Performed electrical diagnostics using clamp meter to verify proper amperage draws and electrical connections throughout the system. Measured and recorded temperature differentials across system components using infrared thermometer to ensure optimal heat transfer and system performance. Inspected all mechanical and electrical components, including capacitor, motor assemblies, and wiring connections. Customer will supply their own 16x20x1 air filter for the system. All tested components operating within manufacturer specifications at time of service.

Responded to kitchen sink clog potentially originating from dishwasher connection. Upon inspection, accessed basement plumbing infrastructure beneath affected fixture and examined drainage system including black PVC vertical drain lines and associated horizontal waste piping. Verified proper venting configuration and assessed condition of drain connections at floor joist level where kitchen plumbing tie-ins are located.

Completed Care Plan tune-up on dual HVAC system with AC/gas furnace units located in basement and attic. Performed comprehensive maintenance on both systems including filter inspection for 14x25x1 and 16x25x4 sizes, temperature differential measurements, and electrical diagnostics. Supply air temperature readings confirmed proper cooling operation at 93.4°F and 96.6°F respectively. Verified electrical components, capacitor operation, and system amperage draw within manufacturer specifications. Both units operating efficiently with no deficiencies noted.

Completed annual AC tune-up on 15-year-old Carrier heat pump system with Infinity Touch thermostat. Performed comprehensive maintenance including inspection of air handler unit located in basement, verified system operation in stage 2 cooling mode with 1050 CFM airflow and 1018 RPM blower speed, confirmed 239V line voltage and proper outdoor coil temperature at 48°F. Replaced 16x25x4 filter included in maintenance plan, inspected PVC condensate drainage, checked refrigerant lines and ductwork connections, and verified thermostat programming and communication with heat pump system.

Responded to service call for steady water leak in basement with associated odor and leak under kitchen sink. Upon arrival, conducted visual inspection of kitchen sink drain assembly and P-trap configuration. Examined chrome drain basket, white PVC P-trap, compression fittings, and horizontal drain line for signs of active leakage or deterioration. Inspected braided supply lines, garbage disposal connections, and all visible plumbing components under sink for moisture, corrosion, or loose fittings. Documented existing plumbing configuration including standard residential drainage setup with white plastic fittings. Assessed basement area for source of water intrusion and odor. No drainage blockages or backup conditions were observed during inspection.

Conducted on-site plumbing estimate for dual-fuel range installation with existing electric and gas connections. Assessed gas piping requirements for warming drawer component, inspecting existing gas supply line routing and connection points within equipment compartment. Documented current configuration and provided recommendations for proper gas line connection to complete installation of heating rack feature.

Responded to callback for urinal drainage issue previously addressed. Upon arrival, inspected plumbing fixture assembly and water supply connections, noting aged valve body with oxidation and corrosion on metal surfaces. Documented existing conditions including braided stainless steel supply lines and wall-mounted shut-off valve showing signs of deterioration. Further investigation required to diagnose persistent drainage problem reported after initial service visit.