Top-Rated Heating, Cooling in Lexington, KY

Performed comprehensive Care Plan tune-up on three gas furnace/air conditioning systems located in basement and closet. Conducted electrical diagnostics using digital multimeter to verify proper amperage readings on blower motors and system components. Inspected and tested all three HVAC units including motors, blowers, and air handler assemblies. Verified thermostat operation and programming on Bryant control unit, confirmed system responding properly in fan-only mode with accurate temperature readings. All systems operational and running within manufacturer specifications upon completion of maintenance service.

Completed full HVAC system replacement under Daikin warranty, including heat pump condenser unit, air handler, and heat kit installation. Removed existing failed equipment and installed new warranty replacement units in exterior side yard location. Documented all model and serial numbers of both old and new equipment with labeled photographs per warranty claim requirements for manufacturer processing.

Completed scheduled maintenance on 20kW Generac standby generator system. Replaced battery, applied identification stickers to both generator unit and transfer switch per customer request, and performed standard maintenance inspection. All equipment operational and functioning within normal parameters.

Responded to no cooling complaint on a 4-year-old electric HVAC system with water leakage at the indoor unit. Upon inspection, found evidence of ongoing drainage issues with wet filter condition and water accumulation at the air handler located in the garage. Performed diagnostic evaluation of the evaporator coil assembly and examined the condensate drain system to identify the root cause of the cooling failure and water leakage that had persisted for three days.

Completed Club Trio maintenance service on four-system HVAC setup consisting of three AC/gas furnace units and one heat pump/air handler. Replaced all air filters per seasonal maintenance schedule: installed two 16x25x3 Lennox filters (X0581), one 16x20x4 filter in Bryant air handler, and one 16x25x1 filter in Bryant furnace located in crawl space addition. Verified proper operation of enerstat System 2 zone control panel and inspected all equipment for proper functionality.

Completed comprehensive preventative maintenance service on Evolution 2.0 air-cooled standby generator with 97.1 run hours. Performed full system inspection including fuel system verification, battery load test, and high/low voltage connection testing. Replaced spark plugs, air filter, and oil filter, then conducted valve adjustment as needed. Verified proper operation in both manual and automatic modes under load conditions, confirming all systems functioning within manufacturer specifications.

Completed comprehensive care plan tune-up on heat pump system. Performed thorough inspection of blower assembly, motor components, and control board, verifying all electrical connections and wire routing. Customer provided their own filter for the service. All system components found operating within normal parameters, with blower wheel and motor assembly showing typical operational wear patterns.

Responded to no heat call for 30+ year old electric AC/furnace system located in closet. Upon arrival, verified system was not operating with no tripped breakers at panel. Accessed indoor air handler unit and inspected electrical components, blower assembly, and control board. Checked supply air temperature at ceiling register using digital thermometer, which confirmed no heated air delivery. Performed diagnostic testing of thermostat communication, transformer voltage, and safety switch circuits. Documented equipment condition with photos showing age-related wear on ductwork connections and air handler cabinet. System requires further troubleshooting of control circuits and potential component replacement to restore heating operation.

Completed annual AC tune-up on rooftop heat pump/air handler system accessed via stairwell. Inspected and photographed pleated air filter showing moderate dust accumulation in return air grille. Performed electrical diagnostics using multimeter, recording voltage reading of 3224 on system components and tested capacitor functionality. All routine maintenance procedures completed per manufacturer specifications.

Completed annual Care Plan tune-up on residential air conditioning system with outdoor condenser unit and gas furnace located in crawlspace. Performed comprehensive maintenance inspection of AC condenser, verified proper operation of all components, and confirmed system performance. Customer-supplied 20x25x1 pleated air filter was inspected and documented during service visit.

Completed Care Plan Tune Up on geothermal HVAC system with indoor unit located in crawlspace. Performed comprehensive maintenance inspection and filter replacement using 18x20x2 and 20x24x2 filters as part of fall service protocol. Inspected and evaluated recently added crawlspace dehumidifier unit, which is elevated on plastic stand supports with condensate pump connection. Examined evaporator coil condition, verified proper fin alignment and cleanliness, and checked electrical connections. All wiring connections were secure with proper color coding observed. Provided estimate for dryer vent cleaning service as requested for future scheduling.

Completed installation of line hide system for new mini split unit at residential property. Concealed refrigerant line set, control wiring, and condensate drain line along exterior wall from outdoor condenser unit to building penetration point. Secured all piping and electrical conduit to exterior siding using appropriate mounting brackets, ensuring professional appearance and protection of components from weather exposure.

Responded to water leak complaint involving supply line to toilet. Upon inspection, identified dampness in wood flooring beneath toilet supply line with no active flow present at time of service. Accessed crawl space to examine PEX plumbing installation and confirmed moisture intrusion affecting subfloor structure. Documented conditions with photographic evidence showing blue PEX piping configuration and exposed floor joists. Advised customer of diagnostic findings and provided recommendations for proper repair procedures.

Completed annual care plan maintenance on air conditioning and gas furnace system located in basement. Performed comprehensive inspection of electrical components including capacitor testing, which measured 252 microfarads and showed normal operation. Verified R410A refrigerant specifications and assessed overall system condition, noting typical wear and dirt accumulation on outdoor unit components consistent with normal environmental exposure.

Completed comprehensive maintenance service on newly installed HVAC system including both air conditioning and gas furnace units. Performed standard tune-up procedures on the AC system utilizing R-410A refrigerant, inspected furnace burner assembly and internal components, verified all electrical connections and controls, and conducted performance measurements in the attic space to ensure proper system operation and efficiency.

# HVAC Service Call - No Cooling with System Freeze-Up Responded to a no cooling complaint on a 5-year-old electric Concord air handler system located in the garage. Customer reported the unit had been freezing up for two days and would only blow air after shutting down to thaw. Upon arrival, the system was already thawed out. Performed visual inspection of the Concord air handler unit and surrounding installation. Examined the indoor air handler cabinet, ductwork connections, condensate drainage system, and accessible refrigerant lines. Inspected flexible ductwork at the supply plenum and verified proper connection to the distribution system. Checked PVC condensate drain lines and tubing for proper pitch and drainage. Documented equipment condition through photographs showing the air handler installation, manufacturer labels, specification plates, and wiring diagrams affixed to the unit cabinet. Noted the system appeared clean and well-maintained with no obvious signs of physical d

Removed existing electrical disconnect and installed a Kohler service entrance rated automatic transfer switch to enable seamless power transition between utility and backup generator sources. Installed a 50-amp generator inlet box with weather-resistant cover on exterior wall, ran appropriate gauge conductors through protective conduit to transfer switch, and completed all necessary terminations per manufacturer specifications and NEC requirements. Performed operational testing with generator to verify proper transfer switch functionality, correct phase rotation, and reliable power delivery to designated circuits.

Responded to customer complaint of foul-smelling water requiring diagnostic testing. Inspected residential water heater system and plumbing connections, including flexible supply lines, PVC piping, and brass fittings. Tested water quality at kitchen sink fixture to identify source of odor issue. Examined water heater condition, noting installation date and current operational status. Evaluated both hot and cold water supply to determine if odor was isolated to water heater or present throughout plumbing system. Recommended appropriate treatment solution based on diagnostic findings to resolve water quality concern.

Completed full installation of RUUD 2-ton 14.3 SEER2 two-stage heat pump system (RP14AY24AJ2NA) with matching 2-ton air handler (RH2TY2417STANNJ) and 10KW heat kit (RXBH-1724A10J-B) in second-floor attic space. Installation included outdoor unit pad with snow legs, electrical disconnect box, whip kit, insulated refrigerant lines with filter, PVC condensate drain system with trap and SS2 coil drain safety sensor, ceiling saver overflow drain pan with water sensor, transition to existing ductwork, standard air filter rack, and digital thermostat. Obtained applicable permits, removed and disposed of existing equipment, and enrolled system in annual maintenance care plan with two semi-annual inspections.

Completed full residential HVAC system installation for first floor consisting of RUUD 2-ton 14.3 SEER2 two-stage heat pump (model RP14AY24AJ2NA), RUUD 2-ton air handler (model RH2TY2417STANNJ), and RUUD 10KW heat kit (model RXBH-1724A10J-B) with digital thermostat. Outdoor heat pump unit installed on concrete pad in backyard with electrical disconnect box mounted on exterior wall, electrical whip kit, refrigerant line insulation, refrigerant line filter, and snow legs for elevated installation. Indoor air handler installation included transition to existing ductwork, standard-sized air filter rack, trap, SS2 coil drain safety water sensor, and ceiling saver overflow drain pan with water sensor for secondary drain protection. Removed and properly disposed of existing equipment per code requirements. Obtained all applicable permits and completed electrical connections including conduit runs from disconnect boxes to outdoor units. System tested and verified operational with proper refrig