Top-Rated Heating, Cooling in Lexington, KY

Provided comprehensive plumbing estimate for rental property conversion, evaluating and documenting shut-off valve replacement requirements throughout the home. Inspected and assessed washer/dryer hookup connections behind access panel, noting existing blue-handled valve and braided supply lines requiring replacement for improved reliability. Evaluated main water shut-off valve accessibility and condition near Lochinvar water heater in basement utility area. Photographed all plumbing components and connections to provide detailed documentation for repair scope and pricing approval.

Completed annual care plan tune-up on Bryant air conditioning system and gas furnace located in basement. Performed comprehensive inspection of outdoor condensing unit and indoor air handler, verified proper operation of Honeywell ProSeries thermostat, checked refrigerant lines and electrical connections, and documented equipment condition with photos per maintenance agreement requirements.

Completed semi-annual preventive maintenance service on commercial HVAC system consisting of six rooftop gas units and one ductless mini-split system with two heads. Performed comprehensive inspection, cleaning, and testing of all equipment including burner assemblies, heat exchangers, blower components, and electrical connections. Inspected and photographed electrical components including capacitors and terminal connections, confirming proper operation and secure mounting. Replaced air filters throughout the system per maintenance agreement specifications, installing multiple sizes including 20x24x2, 16x20x2, and 16x25x2 filters. Verified proper airflow, temperature differentials, and system cycling on all units to ensure optimal performance and energy efficiency for the upcoming season.

Completed monthly club maintenance service on residential heat pump system with air handler located in attic accessible through garage. Performed comprehensive inspection of outdoor condensing unit, verifying proper operation of compressor, condenser fan motor, and electrical connections. Checked refrigerant levels and system pressures within manufacturer specifications. Inspected electrical disconnect, conduit, and wiring for any signs of damage or wear. Cleaned condenser coil and cleared debris from unit perimeter to ensure adequate airflow. Accessed attic-mounted air handler via garage entry point. Replaced existing 20x20x1 Glasfloss air filter with new filter to maintain proper airflow and indoor air quality. Inspected air handler cabinet, blower assembly, and evaporator coil. Verified condensate drain line is flowing freely with no blockages. Checked all electrical connections and safety controls for proper operation. System operating normally with no deficiencies noted at time o

Completed comprehensive Care Plan tune-up service on dual HVAC systems located in attic and closet. Performed full system diagnostics on both air conditioning units and gas furnaces, including electrical testing of capacitors, contactors, and control circuits using precision multimeter. Inspected and evaluated electronic air cleaner and humidifier components. Verified proper system operation, measured electrical parameters, and confirmed all equipment functioning within manufacturer specifications. Customer providing their own 14x25x1 filters for the systems.

Removed and replaced existing Project Source toilet with new American Standard Champion model featuring ADA-compliant elongated bowl. Installed new flexible braided water supply line, secured all connections, tested for proper flush operation and verified no leaks at tank-to-bowl seal or supply line connection.

# HVAC Maintenance - Club Duo Completed Performed comprehensive maintenance service on a Daikin mini-split system located in a downstairs closet. Conducted standard Club Duo preventative maintenance procedures including system inspection, operational testing, and performance verification. During inspection, identified brownish-orange discoloration and staining on condensate drain assembly components, indicating potential fluid leakage or contamination buildup. Documented condition of drain line connections and metallic valve housing where black rubber hose attaches to system. Noted visible wear on rubber hose exterior with surface scratches and scuff marks, though connection remains secure with metal hose clamp in place. Observed dust accumulation on base pan and surrounding equipment surfaces consistent with normal operational environment. Verified system operational status using manufacturer remote control. Confirmed unit responding properly to commands with display showing 74°F s

Completed annual maintenance tune-up on residential air conditioning system and gas furnace unit located in crawlspace as part of preventive care plan membership. Performed comprehensive system diagnostics on outdoor condenser unit using calibrated digital manifold gauges to verify refrigerant pressures and temperatures, confirming proper system charge and operational parameters. All components inspected and found operating within manufacturer specifications, with unit cycling properly and maintaining adequate airflow through condenser coils.

Responded to no cooling complaint on 11-year-old electric furnace/AC system with downstairs zones blowing warm air. Upon inspection, found faulty capacitor affecting compressor operation. Replaced dual-run capacitor, verified proper electrical connections and wire terminations, tested system operation across all zones, and confirmed thermostat communication with equipment resulting in proper cooling delivery to all rooms.

Responded to no heat call on 4-year-old gas furnace system located in walk-out basement. Customer reported thermostat displaying "blower motor fault" message and inadequate heating. Upon arrival, accessed Carrier touchscreen control interface and reviewed system diagnostics. Found active fault code B2-16 VFD System Fault - Low Line Voltage logged on heat pump system, along with previous fault 17-06 Lost BTM Communication. Investigated electrical supply to unit and verified incoming voltage levels. Inspected blower motor assembly, wiring connections, and variable frequency drive components. Checked communication wiring between thermostat and indoor air handler. Cleared fault codes from system memory and cycled unit through operational test. Verified proper system communication restored and heating function operational before departure.

# HVAC Heating System Repair - Control Board Replacement Responded to a no-heat service call on a 9-year-old furnace with heating and fan operation failure. Upon arrival, performed diagnostic testing of the furnace control system using digital multimeter to isolate the malfunction. Inspection revealed failed integrated furnace control board, which had been previously replaced on this unit. Disconnected power supply and removed furnace access panels to access the control compartment. Documented existing wiring configuration and connections prior to removal. Disconnected all wire harnesses from the defective control board, including thermostat wiring, blower motor connections, gas valve control circuits, and safety limit switch connections. Removed mounting hardware and extracted failed control board from cabinet. Installed replacement integrated furnace control board, ensuring proper mounting and secure placement within the control compartment. Reconnected all electrical connections

Completed plumbing inspection of condominium unit to assess bathroom fixture replacement requirements. Evaluated existing conditions of two toilets and two vanities across both bathrooms to provide accurate quote for removal and installation of new fixtures. Documented current plumbing configurations, water supply connections, drain lines, and surrounding tile work to determine scope of work and material specifications needed for replacement project.

Performed routine preventive maintenance on Evolution-branded standby generator unit. Inspected control panel operation, verified AUTO/MANUAL mode functionality, and documented 27.2 limited run hours on digital display. Confirmed unit and exterior components in proper working condition with all controls responding appropriately.

Performed comprehensive air conditioning maintenance tune-up on ground floor HVAC system located in crawl space as part of club membership plan. Inspected air handler unit, capacitor, control board components, condensate drain lines, and ductwork connections; verified all electrical connections secure and system operating within manufacturer specifications. Supplied and installed 20x20x1 air filter included with maintenance agreement.

Completed annual Care Plan tune-up service on basement air conditioning unit. Performed comprehensive system diagnostics using digital refrigerant manifold gauges, recording temperature and pressure readings across the system to verify proper refrigerant charge and operating parameters. All measurements indicated normal system operation with appropriate superheat and subcooling values. Customer provided 16x25x1 filter for replacement during maintenance visit.

Completed Club Duo maintenance service on dual HVAC system. Performed comprehensive inspection of both air conditioning units and gas furnaces, including outdoor condenser unit examination and internal electrical component verification. Inspected and cleaned washable filters located in basement and attic per system configuration. Verified proper electrical connections, refrigerant lines, and control system operation on both units. All equipment operating within normal parameters upon completion of preventive maintenance procedures.

Responded to emergency service call for tanked water heater that received a red tag due to gas leak requiring immediate shutdown. Located and repaired gas leak on same day to restore safe operation of the unit. Tested all connections post-repair to ensure system integrity and proper functionality before returning water heater to service.

Completed annual Care Plan tune-up on Bryant gas furnace and air conditioning system located in basement as part of first-year maintenance included with new furnace installation. Performed comprehensive system inspection, took diagnostic measurements with testing equipment, verified proper operation of all components, and documented equipment condition with photos. Customer provided 20x25x1 filter for replacement during service visit.

Completed comprehensive preventive maintenance service on Generac air-cooled standby generator. Performed full system inspection including fuel system verification, battery electrical testing, and high/low voltage connection testing of all electrical components. Replaced spark plugs, air filter, and oil filter per manufacturer specifications. Conducted thorough examination of generator enclosure interior and exterior, verified proper physical installation and mounting. Tested complete system operation in both manual and automatic modes under load to confirm proper transfer switch functionality and power delivery. All components found in good working condition with system performing to specifications.

Completed comprehensive 60-point visual plumbing inspection of residential property without performing flush tests. Inspected and documented all accessible plumbing fixtures, supply lines, shut-off valves, and exposed piping throughout the home including basement utility areas and bathroom facilities. Verified proper operation of faucets and fixtures, checked for visible leaks or corrosion, and assessed overall condition of plumbing system components with photographic documentation provided for customer records.