Top-Rated Heating, Cooling in Lexington, KY

Completed Gold Level preventive maintenance on dual-system HVAC installation consisting of two gas furnaces and two air conditioning units located in attic and basement areas. Performed comprehensive system diagnostics including amperage draw measurements using clamp meter, which confirmed proper electrical operation at 6.7 amps on tested component. Inspected all major components including capacitors, wiring connections, ductwork, and PVC condensate drainage systems. Both systems operating within normal parameters with no deficiencies noted at time of service.

Completed full residential HVAC system installation including RUUD 2.5 ton two-stage 14.3 SEER2 heat pump (model RP14AY30AJ2NA), RUUD air handler (model RH2TY3617STANNJ), and RUUD 10 KW heat kit (model RXBH-1724A10J-B). Installed Honeywell digital thermostat, combustion floor kit, and insulation downflow kit for proper air handler configuration. Prepared outdoor unit pad by leveling and tamping gravel foundation to ensure stable, compliant placement within HOA requirements, keeping gravel contained strictly under pad perimeter. Installed outdoor unit accessories including snow legs for equipment elevation, electrical whip kit, electrical disconnect box, refrigerant line insulation, and refrigerant line filter. Ran and insulated refrigerant lines between outdoor heat pump and indoor air handler, installed PVC condensate drain line with proper pitch and securing, and connected flexible aluminum ductwork to air handler. Completed all electrical connections including 240V power supply to h

Completed residential installation of Bryant 80% efficiency 70,000 BTU gas furnace (model 800SB36070M17) with removal and disposal of existing equipment. Installed condensate pump with drain line for AC unit, transition to evaporator coil, standard air filter rack, electrical and gas shut-off switches, flexible gas line connector, and flame roll-out protection. Configured flue piping per code requirements using single wall 4" adjustable elbow immediately outside furnace cabinet with double wall vent pipe for remaining run, integrated existing thermostat, obtained applicable permits, and verified all installations meet code compliance standards.

Responded to service call for gurgling freestanding sink in basement. Upon inspection, determined issue was related to plumbing venting rather than drain blockage in the sink itself. Inspected basement plumbing system and toilet fixtures to identify source of air pressure problem causing gurgling sounds. Examined toilet tank components including fill valve assembly, flapper mechanism, and flush valve system. All toilet components were functioning properly with normal water levels maintained. Verified manufacturer specifications on JAMECO 1.6 GPF toilet fixture. No immediate blockages found in visible drain lines. Advised customer that gurgling typically indicates venting issue in plumbing stack that may require further evaluation of vent pipe system to ensure proper air flow and prevent future drainage problems.

Completed Gold Level preventive maintenance on single-system HVAC unit located in garage. Performed standard system inspection, verified electrical connections at outdoor disconnect, and measured supply air temperature at floor register reading 50.7°F. Customer provided filters as specified in maintenance agreement.

Completed drain line repipe in crawlspace to correct improper installation from previous contractor. Removed deteriorated and corroded metal drain piping that showed advanced rust and structural failure. Installed new white PVC drain piping with proper slope, support, and code-compliant fittings throughout the affected section. Secured all new piping to floor joists using metal strapping at appropriate intervals to ensure stability and prevent sagging. Tested the drainage system upon completion to verify proper flow and confirm all connections are leak-free and functioning reliably.

Detected small gas leak on copper fitting connected to yellow flexible gas line during HVAC service call. Upon investigation, determined the leaking line services the fireplace and will require replacement due to corrosion on the fitting and compromised connection integrity.

Completed comprehensive care plan tune-up on heat pump and air handler system located in crawl space. Performed standard maintenance protocols including system diagnostics with digital testing equipment, verified operational parameters, and inspected ductwork insulation integrity. Customer requires 16x20x1 and 18x20x1 filters which are not included in service agreement.

Completed initial care plan tune-up on heat pump/air handler system located in attic with 20x30x1 filter grille in wall. Performed comprehensive inspection of indoor air handler unit, documenting evaporator coil condition and verifying proper electrical connections at heat pump outdoor unit. Both systems were photographed and documented per service requirements, establishing baseline for ongoing maintenance under new care plan agreement.

Responded to callback for water leak following recent gas control valve replacement on water heater. Upon inspection, identified leak at compression fitting on copper supply line near brass valve assembly. Tightened compression fitting and verified all connections at water heater inlet, flexible connector, and associated piping were secure with no active leaks present upon completion.

Completed full residential HVAC system replacement including installation of Lennox 70,000 BTU 93% AFUE gas furnace (ML193UH070XE36BK), Lennox 2.5 ton 14.3 SEER2 air conditioning unit (ML14KC1-030-230), and matching evaporator coil (CK40CT-30/36B-71) with digital thermostat. Removed and properly disposed of existing equipment, obtained necessary permits, and installed outdoor unit on new concrete pad with electrical disconnect box, whip kit, insulated refrigerant lines, and filter drier. Completed furnace installation with transitions to existing ductwork, standard air filter rack, flexible gas line connector with shut-off valve, electrical shut-off switch, flame rollout protection, and connection to flue piping. Installed evaporator coil with proper transitions to ductwork and SS2 coil drain safety water sensor. System tested and verified operational with all safety controls functioning correctly per manufacturer specifications and local code requirements.

Responded to no cooling complaint with system freezing at refrigerant lines. Upon arrival, found air handler operating but producing inadequate cooling with ice formation on suction line. Inspected indoor unit and discovered heavily soiled MERV 8 filter (20x25x1) with significant dust accumulation and debris buildup restricting airflow. Restricted airflow identified as primary cause of evaporator coil freeze-up condition. Recommended immediate filter replacement and system monitoring after thaw cycle to restore proper cooling operation.

Completed full residential HVAC system installation including Bryant 70,000 BTU 80% efficiency gas furnace (Model 800SB36070M14), Bryant 2.5 ton air conditioning unit, and Bryant evaporator coil (Model CVAVA3014XMA). Removed and properly disposed of existing equipment per code requirements. Installed outdoor unit on new concrete pad with electrical whip kit, disconnect box, and insulated refrigerant lines with filter drier. Mounted evaporator coil with transition to existing ductwork and installed SS2 coil drain safety water sensor. Connected furnace to existing flue piping with flame rollout protection, installed flexible gas line connector with gas shut-off switch, and added electrical shut-off switch. Utilized existing filter return grilles and integrated new digital thermostat (Model GA5SAN53000W). Performed complete system startup, verified burner flame characteristics showing proper blue combustion, and conducted comprehensive diagnostics using calibrated instruments. Confirmed a

Completed Care Plan tune-up on heat pump and air handler system located in laundry room. Performed comprehensive maintenance inspection, collected system diagnostics using digital testing equipment at air return vent, and verified proper operation of all HVAC components. Customer provided own filters for the system.

Completed comprehensive Care Plan tune-up on residential air conditioning system with gas furnace unit located in attic access via master bedroom closet. Installed drain safety SS2 device to provide condensate overflow protection. Performed full system diagnostics including electrical measurements with clamp meter showing 0.6 amp draw and environmental readings using digital HVAC analyzer. Replaced customer-supplied air filters (20x30x1 and 12x12x1 sizes) and verified proper airflow throughout system. Inspected all electrical connections, refrigerant lines, and ductwork components. System operating within manufacturer specifications upon completion.

Completed preventative maintenance tune-up on two HVAC systems as part of care plan service - one unit located in basement and one in attic. Replaced air filters on both systems, installing new 16x25x1 GlasFloss filters to ensure proper airflow and system efficiency. Performed standard inspection and maintenance procedures on both air conditioning units and gas furnace units to maintain optimal performance and reliability.

Conducted comprehensive site evaluation for backup generator installation at residential property. Documented existing electrical service entrance configuration, including weatherhead connection, exterior meter base with digital display, and main service panel location on exterior wall. Assessed interior main electrical panel capacity and current circuit breaker configuration to determine available amperage and compatibility for generator transfer switch integration. Photographed existing electrical infrastructure including service entrance conductors, meter socket mounting, panel bus configuration, and existing branch circuit wiring to develop accurate material and labor estimates for 10-12 kW standby generator system installation with automatic transfer switch.

Completed comprehensive maintenance tune-up on four HVAC systems as part of annual care plan service, including two air conditioning units, two gas furnaces, two heat pumps, and two air handlers across main residence and garage apartment. Performed full system inspections, measured supply and return temperatures, verified thermostat operation and calibration, inspected ductwork insulation integrity, and ensured all equipment operating within manufacturer specifications. All systems tested and found functioning properly with no immediate service needs identified.

Completed club membership maintenance visit on 3-year-old gas furnace system located in garage. Performed standard preventative maintenance inspection including visual examination of burner assembly, heat exchanger, and ignition system. Verified proper burner flame characteristics and combustion operation. Inspected all accessible components, electrical connections, and gas piping. System operating within normal parameters. Customer providing their own 16x25 air filters for replacement.

Completed preventative maintenance on 22kW Generac Evolution series standby generator. Performed standard inspection procedures, verified unit operation with 300.4 run hours displayed, and applied identification stickers to both the generator and transfer switch per customer request.