Top-Rated Heating, Cooling in Lexington, KY

Completed preventative maintenance tune-up on residential air conditioning system with gas furnace located in crawlspace accessible through interior closet. Performed comprehensive system diagnostics using clamp meter to verify electrical readings and amperage draws on both indoor and outdoor units. Inspected outdoor condensing unit positioned on concrete pad against brick exterior, confirmed proper operation of compressor and condenser fan assembly, and verified electrical disconnect box connections. Noted that humidifier pad #35 will be supplied during fall maintenance visit as included in membership, and filters will be provided by homeowner.

Responded to no-cooling complaint on upstairs air conditioning system. Upon arrival, found unit running continuously but failing to provide adequate cooling to conditioned space. Performed diagnostic temperature measurements at supply and return air locations. Supply air temperature measured 56°F at ductwork, while return air temperature measured 43.1°F at insulation board near air handler, indicating insufficient temperature split and compromised system performance. System exhibited short-cycling behavior with compressor turning on and off intermittently. Documented conditions with thermal readings for customer records and further evaluation of refrigerant charge, airflow restrictions, or potential compressor efficiency issues common in systems over ten years old.

Completed Gold Level prepaid maintenance tune-up on air conditioning system with gas furnace located in crawlspace. Performed comprehensive inspection of electrical components including capacitor and contactor, verified proper connections and wire terminations. Tested capacitor using digital multimeter, recorded reading of 26.78 MFD to ensure component is functioning within specifications. Customer provided 20x25x1 air filter for installation during service visit.

Responded to no cooling complaint on zoned HVAC system. Performed initial assessment of air handler unit installed in confined vertical chase space. Upon inspection, determined system does not require full replacement as initially suspected. Documented existing equipment condition including control board wiring, drainage lines, and installation configuration. Noted significant moisture concerns and biological growth on surrounding surfaces indicating potential condensate drainage or humidity issues affecting system performance. Recommended follow-up diagnostic service to identify specific cooling failure cause and address underlying moisture problems contributing to equipment stress and indoor air quality concerns.

Removed existing 80-gallon electric water heater from basement utility area and installed new Rheem 80-gallon tanked water heater as replacement unit. Positioned new heater on elevated white metal platform stand to ensure proper clearance and accessibility for future maintenance. Connected unit to existing electrical supply, completing all wiring terminations at terminal block with proper color-coded conductors and secure connections within junction box enclosure. Tied into existing hot and cold water supply lines using copper piping with soldered joints to ensure leak-free connections. Integrated new water heater with existing recirculation system, installing blue recirculation pump assembly on top of unit with appropriate copper pipe connections to maintain continuous hot water delivery throughout the building. Secured all horizontal supply lines to ceiling joists using proper pipe hangers and orange support straps to prevent sagging and ensure system longevity. Completed all plumb

Completed comprehensive plumbing inspection of unpermitted basement bathroom installation to verify code compliance for real estate transaction. Examined all visible plumbing components including supply lines, drain waste vent system, pipe materials, connections, and installation methods throughout the mechanical space. Documented findings with photographic evidence showing copper supply piping, PVC drainage system, water heater connections, and HVAC integration within the confined utility area between floor joists and wall framing.

Responded to water leak complaint with HVAC system dripping through ceiling. Upon inspection, accessed unit and identified condensate drain line issue with excessive dust and debris accumulation throughout the mechanical compartment. Found PVC condensate drain line with visible valve and fittings showing signs of potential blockage or improper drainage. Documented heavily soiled conditions including thick dust buildup on flexible ductwork, refrigerant lines, and surrounding surfaces that may contribute to moisture-related problems. System currently maintaining heating and cooling functionality despite active leak. Photographed wooden shim installation between components and overall condition of confined mechanical space for records. Recommended thorough cleaning of drain line system and removal of accumulated debris to prevent future water intrusion issues.

Conducted on-site electrical assessment for Kohler generator installation. Evaluated existing residential electrical panel configuration, documented current breaker layout and circuit distribution including HVAC systems, major appliances, and general branch circuits. Photographed panel interior showing three-column breaker arrangement with main disconnect and labeled circuits for furnaces, air conditioning units, kitchen appliances, and laundry equipment. Assessed available panel capacity and electrical infrastructure to determine requirements for generator transfer switch integration and load management system.

Completed Gold Level prepaid maintenance service on a dual-system residential HVAC installation consisting of two air conditioning units and two gas furnaces. Performed comprehensive inspection and maintenance procedures on both systems located in attic space, including filter replacement with customer-provided 20x25x1 filters, inspection of ductwork and plenum connections, verification of proper airflow distribution, and assessment of air handler components. All equipment operating within normal parameters with no deficiencies noted at time of service.

Responded to red-tagged furnace with gas leak in exhaust flue pipe. Gas company had identified a hole in the exhaust piping connected to the furnace, requiring immediate repair. Retrieved 4-inch pipe from shop and replaced damaged section of flue exhaust system to restore safe operation and bring unit back into compliance.

Performed comprehensive preventive maintenance on Evolution 2.0 air-cooled standby generator with 97.5 run hours. Conducted complete fuel system inspection, battery electrical testing, and high/low voltage connection verification. Replaced spark plugs, air filter, and oil filter. Inspected generator enclosure interior and exterior for physical condition and proper operation. Verified system functionality through manual and automatic operation tests under load, confirming proper transfer switch operation and power output. Unit operating within manufacturer specifications upon completion.

Installed customer-supplied toilet in the bathroom off the master bedroom. The two-piece unit was properly set, secured, and tested to ensure proper flush operation and no leaks. All connections were verified for proper seal and function.

Responded to water leak above Bradford White water heater originating from vent system in laundry room utility closet. Upon inspection, identified active leak at vent pipe connection and draft diverter assembly above unit. Assessed copper supply lines, brass fittings, and galvanized venting system for source of moisture intrusion. Documented existing water heater installation including plumbing configuration, gas shut-off valve, pressure relief valve, and vent pipe routing. Provided assessment of current system condition and prepared replacement quote per customer request.

Responded to service call for leaking faucets in bathroom tub and kitchen sink. Inspected chrome bathtub faucet assembly and diverter valve for signs of wear and water damage, noting visible spotting on fixtures indicating active leak conditions. Evaluated under-sink plumbing connections at kitchen sink, examining garbage disposal unit, drainage lines, and flexible supply hoses for potential leak sources. Addressed leak issues at both locations to restore proper function and eliminate dripping.

Responded to service call for clogged bathtub drain on main floor. Upon inspection, accessed plumbing infrastructure behind wall cavity and beneath structure to diagnose drainage issue. Found heavily corroded drain assembly and trap components with significant rust and oxidation buildup restricting water flow. Removed wall access panel to examine water supply lines, shut-off valves, and drainage piping. Identified deteriorated metal drain fixture as primary cause of blockage. Cleared obstruction and assessed condition of connecting PVC drainage lines and galvanized piping. Documented existing plumbing configuration including brass fixtures, PEX supply lines, and drain assembly for maintenance records. Restored proper drainage function to bathtub.

Completed comprehensive plumbing inspection in conjunction with scheduled HVAC maintenance visit. Inspected commercial-grade A.O. Smith ProLine water heater installation, verifying proper operation of all components including exhaust venting system, plumbing connections, brass fittings, and safety equipment. Confirmed leak protection pan is properly positioned and PVC protective barriers are secure around unit.

Completed comprehensive maintenance tune-up on three 2-year-old AC systems located in basement, second floor closet, and attic. Performed full system diagnostics including capacitor testing with digital clamp meter showing proper voltage readings, inspected electrical connections and control boards, verified all wire terminations, checked refrigerant pressures, cleaned condenser coils, tested airflow, and confirmed all safety controls and components operating within manufacturer specifications across all three units.

Conducted on-site evaluation of existing 40-gallon gas-fired tank water heater manufactured by Bradford White located in utility closet. Assessed current unit condition, venting system integrity including metal exhaust pipe with foil tape repair, flexible braided stainless steel supply line connections, and overall installation configuration to provide comprehensive replacement estimate for comparable tank-style water heater system.

Performed comprehensive care plan tune-up on 11-year-old heat pump and air handler system located in attic. Responded to STAT message indicating reduced heating performance requiring immediate attention. Conducted thorough electrical diagnostics using digital multimeter to test voltage, amperage, and capacitance values across control board, capacitors, and motor circuits. Inspected all electrical connections, wire routing, and component functionality within both indoor and outdoor units. Verified proper operation of control board, contactors, and safety circuits. Tested system capacitors for proper microfarad ratings and voltage specifications. All electrical measurements recorded and found within manufacturer specifications. System performance restored to optimal operating parameters. Equipment operational at time of departure.

Completed installation of a 40-gallon Bradford White electric water heater (short model, 22" x 47 3/16") in interior utility closet adjacent to laundry area. Removed and replaced existing water heater unit, positioned new tank on drain pan, and made all necessary electrical and plumbing connections to bring system into full operational status. Unit was staged from warehouse inventory and installed per manufacturer specifications with 6-year tank and parts warranty coverage.