Top-Rated Heating, Cooling in Lexington, KY

Performed Club Single maintenance service on air conditioning system located in guest bedroom. Conducted electrical diagnostics using clamp meter, recording amperage draw of 38.1A and voltage readings to verify proper compressor and system operation. Steam humidifier in guest floor area was noted as not covered under the maintenance agreement and was not serviced during this visit. All accessible AC components were inspected and tested to ensure system functionality and performance within manufacturer specifications.

Conducted site assessment for hardwired outdoor Level 2 EV charging station installation. Evaluated existing electrical service panel capacity, verified available breaker spaces, and assessed exterior mounting location approximately 15 feet from main electrical panel. Documented current electrical infrastructure including meter base, existing conduit runs, and panel configuration to determine installation requirements and project timeline for the proposed EV charger installation.

Completed comprehensive electrical estimate for whole-house generator installation at residential property. Assessed existing electrical infrastructure including main service panel located in attic space with current circuit breaker configuration and wiring pathways. Evaluated natural gas meter assembly and supply line capacity mounted on exterior brick wall to determine feasibility for generator fuel source connection. Documented all necessary components including transfer switch requirements, load calculations for essential circuits, gas line sizing specifications, and optimal generator placement considerations. Provided detailed photographic documentation of existing electrical panel, available installation space, and gas utility connection point to develop accurate material list and labor requirements for full generator system integration.

Responded to upstairs toilet with no water supply and inability to flush. Upon inspection, removed tank lid and assessed internal components including fill valve with red cap, flush valve assembly, and flapper mechanism. Identified issue with water supply to tank preventing proper filling and flush operation. Inspected fill valve assembly and water supply line connection. Tank showed low water level with visible mineral deposits and normal wear consistent with infrequent use. Verified no active leaks present in tank or bowl area. Restored water supply to tank, tested fill valve operation, and confirmed proper water level and flush functionality. Unit returned to normal working condition.

Responded to no cooling complaint on 4-year-old electric upstairs HVAC system with intermittent power loss to air handler and thermostat display going dark. Accessed attic-mounted air handler unit via ladder and inspected electrical connections, control board, and safety switches. Found condensate float switch triggering system shutdown due to primary drain line restriction. Cleared drain blockage, verified proper condensate drainage, and tested float switch operation. Cycled system through multiple cooling cycles to confirm proper operation with no further shutdowns. Inspected return air grille showing significant dust accumulation and recommended air filter replacement schedule adherence. System restored to normal operation with thermostat display functioning and unit cooling properly.

Responded to no cool complaint on three-year-old upstairs system with attic-mounted air handler. Performed diagnostic testing on outdoor condensing unit using clamp meter to measure compressor amperage and voltage readings. Measurements indicated compressor operating at 6.03 amps with 0.4 volts initially, then recorded secondary reading of 7104 on refrigerant line. Documented electrical connections and component operation with photos for service records.

Performed comprehensive assessment of existing 38-gallon short electric storage tank water heater located in utility closet. Documented current unit specifications and installation conditions through photographic evidence. Inspection revealed significant rust and corrosion on drip pan beneath water heater, with extensive water damage and staining present on surrounding flooring materials including both tile and adjacent hardwood surfaces. Observed moisture-related discoloration extending from base of unit, indicating active or recent leaking condition. Evaluated utility closet installation space, clearances, and existing plumbing connections to provide accurate replacement estimate for customer consideration of tank or tankless water heater options.

Responded to service call for clogged condensate drain line with leaking drain pan. Upon arrival, accessed air handler unit in attic space and confirmed AC system was operating and cooling properly. Inspection revealed accumulated debris and sediment in the condensate drain pan, with visible dirt buildup indicating drainage restriction. Cleared clog from condensate drain line to restore proper drainage flow and prevent overflow conditions. Cleaned drain pan of accumulated debris and verified proper condensation evacuation. System returned to normal operation with condensate draining freely through primary drain line.

Relocated and raised galvanized water supply lines to accommodate structural support beam replacement in basement crawl space. Rerouted existing water distribution piping using PEX connections to provide adequate clearance above the new support beam location while maintaining proper pitch and support. All water lines were secured to floor joists with appropriate hangers and tested for proper flow and pressure upon completion.

Installed a fan-powered humidifier on the existing forced-air furnace system. Connected the unit to the main supply ductwork, established proper drainage to the condensate pan, and wired the humidistat for automatic operation. Customer will remit payment by check.

Replaced damaged outdoor electrical disconnect serving commercial HVAC condenser unit with new 60-amp Square D QO series disconnect switch. Removed old weathered disconnect panel, installed new enclosure on exterior concrete block wall, and reconnected all power conductors and grounding wires to proper terminals within the new disconnect box.

Completed monthly Gold Level preventive maintenance on single heat pump/air handler system located in utility room. Performed comprehensive system inspection including temperature readings and airflow verification. Supply air temperature measured at 104.5°F during heating mode operation. Inspected 16x25x5 media filter housing and confirmed proper fitment. Customer provides their own filters per service agreement. Verified all mechanical components operating within normal parameters. System functioning properly with no deficiencies noted at time of service.

Responded to no cooling call for 3-year-old heat pump system. Upon arrival, confirmed thermostat had no power and display was blank. Performed diagnostic testing on HVAC system components in attic location. Traced low voltage wiring from air handler to thermostat, checking transformer output voltage and circuit continuity. Identified power supply issue preventing thermostat operation. Completed necessary repairs to restore 24V power to thermostat circuit. Verified air handler and heat pump operation, confirmed system cooling properly and thermostat functioning normally. All equipment covered under existing parts and labor warranty. System returned to normal operation with cooling restored.

Responded to no cooling complaint on 3-year-old attic-mounted air conditioning system. Upon arrival, found thermostat displaying 83°F with system running in cooling mode but failing to achieve setpoint. Inspected air handler unit in attic and confirmed reported melted foam insulation component within the cabinet. Examined evaporator coil assembly, ductwork connections, and internal components for additional damage or airflow restrictions. Documented conditions with photographs showing dust accumulation on interior surfaces and melted insulation material. System requires replacement of damaged insulation component and further diagnostic evaluation to determine root cause of overheating and cooling failure.

Completed new installation commissioning and full system verification for 26KW Generac next-generation standby generator. Performed comprehensive testing of all electrical connections, verified proper operation of transfer switch assembly with circuit breakers and contactors, confirmed correct installation of exterior service disconnect panel and metering equipment, and validated proper conduit routing and cable management throughout the installation. Inspected internal generator control components including wiring harnesses, circuit protection devices, and digital control unit to ensure compliance with manufacturer specifications. Registered unit and completed commissioning procedures, confirming system readiness for automatic operation during power outages.

Responded to service call for non-operational garbage disposal unit with no humming noise. Upon inspection, found 5-year-old 1.3 horsepower disposal unit completely unresponsive, indicating electrical failure or motor seizure. Removed and replaced defective garbage disposal unit with new assembly, reconnecting all drain lines, dishwasher discharge hose, and electrical supply. Verified proper P-trap configuration, tested all connections for leaks, and confirmed new unit operates correctly with full grinding capability.

Completed comprehensive AC tune-up on 9-year-old residential heating and air conditioning system with no reported issues. Performed standard preventive maintenance including inspection of ductwork in crawlspace, verification of electrical connections at outdoor unit capacitor, and system performance testing. Replaced existing thermostat per customer request and confirmed all components operating within manufacturer specifications.

Completed site evaluation for Feel the Love program qualification to assess existing HVAC system and ductwork infrastructure. Inspected interior spaces including bathroom area with return air ventilation and documented equipment specifications through detailed measurements and photography. Confirmed presence of existing ductwork system and verified equipment nameplate information to determine system compatibility and eligibility for program participation.

Responded to callback for reported loss of hot water following previous venting service. Upon arrival, inspected dual water heater installation in basement mechanical room and evaluated all associated supply lines, distribution piping, and connections to both units. Determined hot water issue was unrelated to original venting work performed, and customer was advised of service charge for diagnostic visit per company policy.

Responded to callback for recently installed HVAC system with insufficient cooling and overflowing drain pan. Upon arrival, verified thermostat set to 71°F with ambient temperature at 78°F. Inspected indoor unit and found drain pan at capacity, indicating condensate drainage issue. Measured supply air temperature at 39.9°F, confirming proper refrigerant charge and compressor operation. Addressed drainage blockage and verified proper system operation before departure.