Top-Rated Heating, Cooling in Lexington, KY

Completed scheduled care plan maintenance on upstairs air handler unit. Inspected evaporator coil assembly, noting accumulated dust and debris on fins with minor compression in several areas. Performed electrical diagnostics using clamp meter, recording amperage reading of 4.48 amps on system components. Documented equipment condition through photographs showing heat exchanger fins with oxidation and discoloration consistent with normal operation. All measurements within acceptable operating parameters for continued system performance.

Completed comprehensive air conditioning tune-up and routine maintenance on a six-year-old residential AC system. Performed standard preventive maintenance procedures including inspection of outdoor condensing unit, verification of electrical connections at disconnect box, assessment of unit mounting and pad stability, and documentation of equipment condition. System found operating within normal parameters with no deficiencies noted. Unit exterior and surrounding area photographed for service records, showing proper installation on concrete pad against brick foundation with adequate clearance and access for future service.

Completed Gold Level prepaid maintenance on single-system HVAC unit with AC and gas furnace located under stairs. Performed thorough cleaning of outdoor condenser coil, inspected and tested furnace operation to ensure readiness for heating season, and cleared condensate drain line which showed visible mold growth. Replaced 16x25x1 air filter, verified system electrical readings showing 35.35 volts at condenser unit, and confirmed proper operation of all components.

Responded to callback for toilet leak two months post-installation. Inspection revealed compromised wax ring seal at floor flange connection. Removed toilet, replaced wax ring and closet bolts, reinstalled and tested unit to confirm proper seal with no active leaks detected.

Responded to system fault error displayed on heating and cooling unit while system remained operational. Inspected air handler unit in utility closet, verified refrigerant lines and electrical connections, and confirmed outdoor sensor module was properly mounted and functioning. Checked air filtration system and determined all components were operating within normal parameters despite error code display.

Responded to service call for leaking outdoor spigot at rear of property and low water pressure in master bathroom. Upon inspection, accessed wall cavity behind affected spigot and identified deteriorated copper piping connections causing the leak. Repaired compromised 90-degree elbow joint and horizontal pipe section, restored proper seal at wall penetration points, and verified all connections for integrity. Water pressure issue in master bathroom was resolved through system inspection and adjustments, restoring normal flow throughout the residence.

Serviced two HVAC systems in basement. Unit #1: 20-year-old Rheem system received new 10 MFD and 30 MFD capacitors, disassembled and cleaned condenser coil, cleaned evaporator coil, and installed drain safety switch. Unit #2: 11-year-old Carrier system received new 35/5 MFD dual capacitor, disassembled and cleaned condenser coil, cleaned evaporator coil, and installed drain safety switch. Replaced three 16x20x1 air filters. All systems tested and operating properly upon completion.

Completed comprehensive Care Plan tune-up on heat pump and air handler system located in third-floor knee wall area, with unit age exceeding 10 years. Performed diagnostic testing using digital multimeter, recording electrical readings at 456 on system components including gas valve assembly, copper refrigerant lines, and control wiring. Inspected Goodman furnace installation, PVC venting system, ductwork connections, and all mechanical components for proper operation and safety compliance.

Responded to a no cooling call on a 10-year-old electric HVAC system for a second opinion evaluation. Upon arrival, performed diagnostic testing of the outdoor unit's electrical components, including amperage draw measurements on the compressor circuit using a clamp meter, which registered 449 amps. Inspected the run capacitor and contactor relay for proper operation and physical condition. Evaluated the system's refrigerant circuit based on the previous company's assessment of a refrigerant leak requiring a seal replacement. Checked the programmable thermostat in cooling mode, which was set to 67°F with a scheduled setpoint of 65°F. Verified recent filter maintenance had been completed. Provided findings and recommendations to the customer regarding the system's condition and available repair versus replacement options for their upstairs bedroom unit.

Completed comprehensive spring maintenance tune-up on residential HVAC system. Performed electrical diagnostics using clamp meter to verify proper amperage draw and system performance, inspected control board wiring and connections, and evaluated overall system operation. All components found operating within normal parameters with no issues identified during inspection.

Completed comprehensive care plan maintenance service including air conditioning system, gas furnace, and humidifier tune-up for unit #35 located in crawl space. Customer-supplied air filter (20x25x1 3M Filtrete) was installed, and billable humidifier pad replacement was performed. Verified proper operation of dual-zone climate control system with Honeywell HumidPRO humidistat and programmable thermostat, confirming heating mode functionality and accurate temperature readings at 70°F setpoint.

Completed TXV replacement on residential HVAC system with successful refrigerant recovery and reuse. Performed system evacuation, installed new thermostatic expansion valve, and recharged system with recovered refrigerant. Verified proper system operation with manifold gauge readings showing appropriate pressures and confirmed supply air temperature of 65.3°F at ductwork, indicating adequate cooling performance.

Responded to service call for HVAC unit operating in heat mode when thermostat was set to cooling. Inspected system wiring and electrical connections, reviewed previous inspector documentation and photographs regarding condensate line discharge locations and equipment specifications. Assessed whether current equipment capacity is appropriately sized for the property's heating and cooling load requirements.

Completed routine maintenance inspection on three-year-old air conditioning system as part of preventative maintenance agreement. Performed comprehensive tune-up including visual inspection of attic-mounted air handler and ductwork, electrical testing of system components using clamp meter to verify proper amperage draw and voltage levels, and verification of all mechanical operations. System found operating within manufacturer specifications with no deficiencies noted. Unit maintained in good working condition.

Completed comprehensive maintenance tune-up on heat pump and air handler system located in kitchen closet. Performed thorough inspection of all system components with particular attention to refrigerant levels as requested due to previous lineset repair history. Checked refrigerant charge and verified proper operation following earlier installation issues involving kinked lineset that required splicing and leak repair. Inspected air handler unit and documented significant deterioration of drain pan showing heavy rust staining and accumulation of dirt, grime, and moisture residue. The condensate collection tray exhibited brown and orange discoloration around edges with dark contamination on interior surfaces, indicating need for future replacement consideration. Examined reflective insulation surrounding unit showing some white residue and staining. Evaluated air filtration system with customer-provided 16x16x1 filter, noting dust and debris accumulation on pleated filter surface. Ins

Responded to no cooling call on 1-year-old electric HVAC system displaying system alert at thermostat. Upon arrival, found air handler installed in laundry room with multiple replacement filters staged nearby. Performed diagnostic evaluation of indoor unit and electrical connections. Inspected wire terminations at unit with orange wire nuts visible at top connections. Verified filter had been changed approximately one month prior. System alert condition preventing cooling operation was addressed, restoring normal functionality to the air conditioning system.

Performed comprehensive Care Plan tune-up service on air conditioning system and gas furnace equipment located in crawlspace. Completed thorough inspection of burner assembly, heat exchanger components, and all mechanical systems per maintenance protocol, with customer providing air filters for installation.

Completed comprehensive AC tune-up maintenance on dual-zone system with heat pump/air handler units located in basement and attic. Performed electrical diagnostics using digital multimeter to verify proper voltage and amperage across all circuits, inspected internal wiring connections and transformer components, and replaced customer-supplied air filters (20x20x1 and 25x25x1). All systems tested and operating within manufacturer specifications.

Completed comprehensive Care Plan tune-up on dual-system HVAC installation consisting of heat pump/gas furnace and gas furnace/air conditioner units installed in 2023. Performed preventive maintenance inspections on air handler unit located in crawlspace and attic-mounted equipment, verifying proper operation of refrigerant lines, condensate drainage systems, electrical connections, and ductwork integrity. Documented equipment conditions with thermal and visual measurements to ensure optimal system performance.

Completed annual Care Plan maintenance tune-up on basement AC/gas furnace unit with 16x25x4 filter. Performed comprehensive system inspection, took electrical amp draw readings using clamp meter showing 0.64A, verified proper operation of all mechanical components, and documented equipment condition with photos of internal assembly and electrical connections.