Top-Rated Heating, Cooling in Lexington, KY

Completed routine AC tune-up on 7-year-old air conditioning system during scheduled maintenance visit. Performed comprehensive system inspection including visual assessment of furnace and mechanical equipment in basement, verified proper air filter installation, and conducted electrical diagnostics on outdoor condensing unit using clamp meter to measure amperage draw and confirm system is operating within manufacturer specifications. All components found to be functioning properly with no issues identified requiring immediate attention.

Completed planned maintenance service on Bryant heat pump system located in loft area above offices. Performed comprehensive fall maintenance inspection including temperature diagnostics on supply ductwork, recording 69.0°F at duct surface using calibrated digital thermometer. Inspected insulated ductwork in attic space for proper wrapping and thermal integrity. Conducted exterior inspection of condenser unit, verifying proper installation on concrete pad, checking electrical disconnect, refrigerant line connections, and overall unit condition. System operating within normal parameters with no issues identified during maintenance visit.

Responded to service call for downstairs HVAC system not operating with E1 error code displaying on thermostat. Inspected control board and electrical connections in basement air handler unit. Verified all wire terminations secure at terminal blocks, checked capacitors and control circuitry for proper operation. Documented control board configuration and wiring connections. System evaluated for any correlation to recent service work performed at property.

Investigated temperature discrepancy on existing Honeywell thermostat displaying 76°F while set to 72°F. After diagnosing the issue, removed the old thermostat and installed two new Ecobee smart thermostats to resolve the temperature control problem and provide improved system performance.

Completed comprehensive preventive maintenance tune-up on dual HVAC system consisting of two heat pumps and two air handlers as part of Care Plan service. Performed electrical diagnostics using calibrated testing equipment, measuring amperage at 26.7A and voltage at 24.65VAC to verify proper system operation and component functionality. Inspected capacitors, relay boards, electrical connections, and condenser coils on both outdoor units to ensure optimal performance and system reliability.

Completed preventive maintenance tune-up on Ameristar mini-split system with four indoor air handler heads. Performed comprehensive inspection of all zones, verified operational temperatures with infrared thermometer confirming proper cooling output at 49.1°F, and documented system performance through diagnostic testing of wall-mounted units.

Conducted on-site assessment for gas line installation to supply existing fireplace. Inspected crawlspace access route and evaluated structural pathway for new gas piping from main supply to fireplace location. Documented existing conditions including crawlspace joists, insulation clearances, and concrete block foundation walls to determine optimal routing for code-compliant installation.

Responded to warranty call for outdoor unit noise complaint. Inspected HVAC system including attic components and outdoor unit electrical connections. Documented system condition with photos showing ductwork, insulation, and control wiring with multiple wire connections secured by wire nuts and capacitor assembly. Awaiting manufacturer approval from Rheem for potential unit replacement per established warranty protocol.

Removed existing chrome sink drain assembly and installed new tubular PVC drain system with proper trap configuration at utility sink. Cut out deteriorated gate valve on main water supply line and replaced with new quarter-turn ball valve to provide reliable shutoff capability. Re-inspected previously repaired faucet that continued to leak, identified persistent issue, and completed necessary adjustments to achieve proper seal and eliminate leaking condition. All plumbing connections tested and verified leak-free upon completion.

Completed annual tanked water heater maintenance and flush service as part of the USA Bronze preventative maintenance program. Inspected water heater installation in crawl space area, including supply and drain plumbing connections, verified proper pipe support and insulation integrity, and documented existing plumbing configuration with PVC drainage system and copper supply lines. Performed standard water heater flush procedure to remove sediment buildup and ensure optimal performance and efficiency.

Completed bathroom renovation plumbing work including removal of existing sink and toilet fixtures. Successfully reinstalled customer-supplied toilet with new water supply line connection and angle stop valve, ensuring proper sealing and functionality. Removed and hauled off old toilet fixture from premises as requested, leaving work area clean and ready for continued renovation activities.

Completed scheduled Care Plan tune-up on attic-mounted air conditioning and gas furnace system. Performed comprehensive diagnostic testing using digital multimeter to verify electrical components and system operation. Inspected and tested capacitor, control board connections, and all electrical circuits to ensure proper voltage and functionality. All components found operating within normal parameters and system running efficiently.

Completed comprehensive Care Plan tune-up service on residential heat pump and air handler system. Performed thorough inspection of Rheem furnace unit and associated components, including detailed examination of electrical contactor assembly, terminal connections, and control wiring. All system components found operating within normal parameters, with routine maintenance procedures completed per manufacturer specifications.

Completed plumbing repair in basement by cutting out and replacing leaking copper pipe section, replaced toilet wax ring to restore proper seal, and installed new reverse osmosis system under kitchen sink with full functionality verification. All water supply lines, shutoff valves, and connections were properly secured and tested for leaks before departure.

Completed comprehensive Care Plan tune-up on heat pump and air handler system located in garage. Performed electrical diagnostics using digital multimeter, measuring capacitance at 5.05 μF and verifying system amperage at 0.63A with 0.1V readings to ensure proper compressor and motor operation. All components tested within manufacturer specifications and system operating efficiently.

Responded to no-cooling complaint on 3-year-old electric heat pump system potentially damaged during recent ice storm. Performed Club Duo maintenance on heat pump and gas furnace units located in attic and crawl space. Utilized digital manifold gauges to diagnose refrigerant system, measuring operating pressures and temperatures on both high and low sides of the system. Inspected copper refrigerant lines showing heat discoloration and oxidation at service port connections. Completed comprehensive maintenance procedures including system performance evaluation, refrigerant charge verification, and visual inspection of all accessible components. Customer-provided filters were due for replacement during service visit. System diagnostics and maintenance performed to restore cooling functionality and ensure proper operation for upcoming cooling season.

Completed routine preventive maintenance on Carrier residential standby generator. Performed visual inspection of unit exterior and internal components, verified main 7.5 AMP fuse condition, confirmed proper control panel operation with LCD display showing 227.6 run hours, tested auto/manual switch functionality, and ensured unit readiness for automatic operation during power outages.

Successfully completed drainage system upgrade by connecting to existing galvanized discharge line and replacing with new 1.5-inch PVC pipe. Ran the upgraded discharge line past landscaping bushes to proper termination point in yard for improved drainage flow. All materials installed and system tested for proper operation.

Conducted comprehensive electrical estimate for generator installation at residential property. Evaluated existing electrical infrastructure including main service panel, meter base, and exterior utility connections mounted on brick wall exterior. Assessed current electrical service capacity and determined optimal routing for generator connection conduit. Documented existing weathered outdoor plumbing fixtures and utility equipment locations to plan appropriate clearances and code-compliant placement for standby generator system. Photographed site conditions including brick wall mounting surfaces, existing conduit runs, and ground-level access points to develop accurate material list and labor requirements for complete automatic transfer switch installation and generator pad preparation.

Completed scheduled care plan maintenance on upstairs air handler unit. Inspected evaporator coil assembly, noting accumulated dust and debris on fins with minor compression in several areas. Performed electrical diagnostics using clamp meter, recording amperage reading of 4.48 amps on system components. Documented equipment condition through photographs showing heat exchanger fins with oxidation and discoloration consistent with normal operation. All measurements within acceptable operating parameters for continued system performance.