Top-Rated Heating, Cooling in Lexington, KY

Responded to no cooling complaint on 10-year-old AC unit. Upon arrival, confirmed air handler operational but compressor not engaging. Performed diagnostic evaluation of control board and electrical connections, inspecting terminal blocks, wire connections, and PCB components for proper voltage and continuity. Documented control board wiring configuration and connection points. Identified compressor circuit issue preventing outdoor unit operation. Photographed control board assembly showing terminal connections and component layout for service records.

Completed preventive maintenance tune-up on air conditioning system and gas furnace unit located in crawl space as part of care plan service. Installed customer-supplied 20x25x4 air filter and performed comprehensive system inspection, including electrical diagnostics with amperage readings confirming proper compressor operation at 62.5 amps and capacitor functionality verification.

Responded to no cooling complaint at commercial church facility. Upon inspection, found blower motor assembly heavily contaminated with dust and debris buildup, restricting airflow and causing system performance issues. Measured supply air temperature at 57.5°F, confirming reduced cooling capacity. Documented motor condition and ductwork assembly showing significant dirt accumulation on mounting brackets and electrical connections. Identified need for thorough system cleaning and potential motor servicing to restore proper airflow and cooling function.

Completed routine preventive maintenance on standby generator unit. Inspected control panel, verified main 7.5 amp ATO fuse integrity, confirmed AUTO/MANUAL selector switch operation, and documented 280.8 run hours on the digital display. All control functions and monitoring systems tested and found operating within normal parameters.

Completed kitchen sink faucet replacement on return visit. Successfully installed modern three-piece faucet system with pull-down spout and dual lever handles in brushed stainless steel finish. Connected all supply lines and verified proper operation with no leaks detected beneath undermount sink installation.

Responded to no cooling complaint at commercial daycare facility with electric HVAC system. Upon inspection, found heavily soiled air filter restricting airflow to the system, which had not been changed in approximately one year. Replaced dirty filter with new unit to restore proper airflow and system operation. Verified outdoor disconnect and electrical components were functioning properly. System restored to normal cooling operation.

Completed electrical installation of new Generac backup generator system at residential property. Relocated existing generator unit and installed new generator on gravel pad with proper grounding and conduit connections. Performed all electrical panel integration work, including breaker installation, load center wiring, and transfer switch connections to ensure seamless automatic power transfer during utility outages. Verified all electrical connections meet code requirements and tested system operation for proper functionality.

Relocated sump pump discharge line from sewer connection to exterior yard drainage system. Capped original connection point at sewer line and routed new discharge piping from crawl space through buried trench to backyard, terminating at pop-up emitter for proper water dispersal. Backfilled excavated trench, applied seed and straw to disturbed areas, and verified complete sump pump operation and discharge function upon project completion.

Completed annual maintenance visit on gas furnace, air conditioning system, and humidifier unit as part of scheduled fall/winter preventive maintenance program. Performed comprehensive system inspection with panel removed to access internal electrical components and wiring. Utilized digital clamp meter to verify electrical performance, recording operating amperage of 42.41 amps and voltage reading of 243.0 volts to confirm proper system operation. Inspected all electrical connections, including yellow, red, and white wiring harnesses, and examined copper refrigerant lines for integrity. All components found operating within normal parameters with no deficiencies noted. System left in proper working condition.

Responded to warranty callback for recent HVAC installation to address return plenum deficiencies and secondary drain pan water accumulation. Upon inspection, found return plenum tab at filter rack had detached from original installation. Re-secured, sealed, and properly supported return plenum components to manufacturer specifications. Investigated secondary drain pan water presence, identified drainage issue, and corrected accordingly to ensure proper condensate flow and prevent future standing water conditions.

Responded to service call for downstairs bathroom faucet with no hot water production. Upon arrival, coordinated property access through realtor. Diagnosed issue as failed cartridge in hot water valve assembly of three-handle widespread bathroom faucet with brass finish. Disassembled hot water control valve, removed defective cartridge containing worn internal seals and O-rings. Installed replacement cartridge assembly, ensuring proper seating and alignment within valve body. Reassembled faucet handle with porcelain accent piece and tested operation. Verified full hot water flow restoration and proper temperature mixing capability. Faucet now operating correctly with balanced hot and cold water delivery.

Responded to no heat call on gas furnace system less than 10 years old. Upon arrival, verified thermostat was not switching from cooling to heating mode, preventing system operation. Inspected Honeywell Home thermostat model TH2211017DG and identified malfunction preventing mode changeover. Removed thermostat from wall mount and examined internal circuit board and wiring connections. Confirmed supply air temperature at floor register measured 58.2°F, indicating lack of heat delivery. Diagnosed thermostat failure as root cause of heating system lockout. Reviewed system operation with homeowner and provided recommendations for thermostat replacement to restore proper heating function.

Completed routine 60-point plumbing inspection per customer request with 30-minute advance notification provided. Performed comprehensive visual assessment of under-sink plumbing configuration, including white PVC trap assembly, chrome tailpiece, and sink drain basket connections. Inspected all accessible pipe joints, mounting brackets, and drain components for signs of leaks, corrosion, or deterioration. Verified proper drainage function and confirmed all plumbing fixtures were secure and operating within normal parameters. Documented findings with photographic evidence showing cabinet interior conditions and plumbing infrastructure. No immediate repairs required at time of inspection.

Responded to no cooling complaint on 23-year-old electric air conditioning system with indoor unit located in attic accessed through upstairs closet. Upon arrival, verified thermostat was set to cooling mode and calling for 77 degrees but system was unresponsive. Inspected outdoor condenser unit and found unit would not power on. Diagnosed failed contactor preventing compressor and condenser fan operation. Replaced contactor, restored power to system, and verified proper startup sequence. System now cooling effectively with normal amperage draw on compressor and condenser fan motor operating within manufacturer specifications.

# HVAC Cooling System Diagnostic and Repair Responded to service call for 12+ year old Bryant cooling system with complaint of outdoor compressor not activating while indoor air handler continued to operate. Upon arrival, performed initial system assessment and temperature readings at supply register, which measured 51.3°F, indicating insufficient cooling performance. Conducted comprehensive diagnostic evaluation of electrical and control systems. Inspected indoor air handler control panel and identified issues with low voltage control wiring and connections. Examined thermostat circuit, contactor operation, and associated control components including gas valve assembly and safety controls within the air handler cabinet. Traced low voltage wiring from indoor unit to outdoor condensing unit to isolate failure point preventing compressor engagement. Verified proper voltage at thermostat and indoor control board. Testing revealed faulty or interrupted signal to outdoor unit preventing

Responded to service call for water leak at indoor air handler unit located in hallway closet. Upon arrival, found small amount of water accumulation at base of unit. Inspected condensate drain system and confirmed blockage in condensate drain line as suspected. Cleared clog from drain line, verified proper drainage flow, and tested system operation to ensure leak was resolved.

Responded to water leak investigation affecting multiple units with steady leaking from ceiling. Located source of leak in structural cavity where heavily corroded horizontal supply piping exhibited severe rust deterioration and active moisture infiltration at pipe joint connections. Documented extensive corrosion damage to metal piping system requiring replacement, with photographic evidence showing compromised pipe integrity and wet conditions at fittings within wooden floor joist assembly.

Installed 1" gas piping from main gas line to new generator location. Ran pipe into garage, routed exposed across ceiling, then exited through back of garage. Piping was installed high under the eave and positioned over doors to maintain clearance to generator connection point. Gas line includes proper shut-off valve and complies with code requirements for generator fuel supply.

Completed full residential HVAC system installation for first floor heating and cooling. Installed RUUD 14.3 SEER2 two-stage 2-ton heat pump condenser unit (model RP14AY24AJ2NA) on exterior pad with proper leveling and positioning. Mounted RUUD 2-ton air handler (model RH2TY2417STANNJ) in attic space and integrated with existing ductwork system. Installed RUUD 10KW heat kit (model RXBH-1724A10J-B) for supplemental heating capacity. Ran refrigerant line set from attic air handler through exterior wall to outdoor condenser unit with proper insulation and securing. Installed new 14x14 return air grille on second floor stair landing to provide adequate return air flow for first floor system. Fabricated and installed return air ductwork from new grille location to air handler. Modified existing duct system with miscellaneous fittings and adapters to ensure proper integration and airflow distribution. Removed and disposed of existing equipment per standard procedures. Connected refrigerant l

Successfully completed installation of a Bryant 15.2 SEER2 3-ton heat pump system with matching air handler and 15KW heat kit for second floor zone. Installed outdoor condenser unit on concrete pad with snow legs, electrical disconnect box, and whip kit, then ran insulated refrigerant lines with filter to indoor air handler. Mounted air handler with overflow drain pan equipped with water sensor, coil drain safety sensor, and proper trap, then integrated 20x30 filter return grille to replace existing undersized 20x25 grille and transitioned to existing ductwork. Installed digital WiFi thermostat for remote system control and monitoring. Removed and disposed of all existing equipment, obtained necessary permits, and verified system operation with proper refrigerant charge and airflow. System is now providing efficient heating and cooling with enhanced safety features and code-compliant installation.