Top-Rated Heating, Cooling in Lexington, KY

Completed routine HVAC maintenance on attic-mounted air conditioning and gas furnace system as part of club membership service. Inspected outdoor condenser unit with protective grille, verified proper operation and drainage, examined ductwork and air handler components for wear and airflow efficiency, and documented system condition with photographic evidence. Customer provided 20x25x1 filter for installation during service visit.

Completed comprehensive heating and air conditioning maintenance inspection on a 2-year-old HVAC system located in basement. Performed standard tune-up procedures on the air handler unit, verified thermostat operation showing proper heating mode functionality at 75°F, and inspected all mechanical components including PVC condensate lines, copper refrigerant lines, and gas connections. System found to be operating within normal parameters with no issues identified; customer providing their own 20x25x4 filters for the unit installed in July 2024.

Completed annual air conditioning maintenance as part of club membership plan. Performed electrical diagnostics on outdoor condensing unit, measuring voltage at 241.7V and amperage readings of 5.884A with Fieldpiece clamp meter. Tested capacitor functionality and verified all electrical connections were secure. Changed customer-provided filter as requested. All system components operating within normal parameters upon completion of tune-up service.

Completed comprehensive Care Plan tune-up on dual-zone HVAC system consisting of two gas furnaces and two air conditioning units located in basement and attic. Performed thorough inspection and testing of Daikin furnace in basement, including visual assessment of unit condition, venting system integrity, and ductwork connections. Conducted electrical diagnostics on outdoor AC condenser unit, measuring capacitor voltage which registered 26.6 volts, indicating proper operation within manufacturer specifications. Verified all safety labels present and legible, confirmed PVC intake and exhaust venting properly installed, and checked for proper drainage with no active leaks observed. Customer provided their own filters for both systems as part of maintenance agreement.

Completed Gold Level prepaid maintenance on a 12-year-old heat pump and air handler system located in laundry room and sun room. Performed comprehensive inspection and diagnostic testing including electrical measurements using clamp meter, recording amperage and voltage readings to verify proper system operation. Mini-split unit was excluded from service per customer request, with maintenance focused solely on the main HVAC unit. Customer provided filters for the service visit.

Completed installation of Carrier Comfort Series 80% AFUE 90,000 BTU gas furnace model 58SB0B090M21-16 in attic space. Installed two Honeywell TH2110WF4008/U WiFi smart thermostats for multi-zone control. Work included transition connection to existing evaporator coil, standard-sized air filter rack installation, connection to flue piping system, electrical disconnect switch, gas shut-off valve, flexible gas line connector, and flame roll-out safety protection. All ductwork connections secured to furnace plenum with proper sealing. Verified proper combustion air supply and venting configuration per manufacturer specifications. Installed PVC condensate drain line with trap and routed to approved drainage location. Completed all electrical wiring to code including 120V power supply and thermostat low-voltage wiring. Tested gas pressure at manifold and adjusted for optimal burner performance. Conducted system startup procedures including ignition sequence verification, blower motor operat

Rerouted sump pump discharge line through the front of the home with outlet to street, requiring penetration through exterior wall. Installed bucket pump system for washing machine drainage with dedicated vent line through second wall penetration. Secured all PVC discharge piping and connections in crawl space with proper mounting hardware, installed valve assembly on vertical discharge line, and verified complete system operation with no leaks detected at any connection points.

Installed dedicated electrical circuit and wiring to supply power to newly installed mini-split HVAC system on exterior of residential structure. Ran conduit and electrical lines from main panel to outdoor condensing unit location, ensuring proper voltage supply and code-compliant installation for equipment operation. System was tested and verified operational upon completion.

Responded to service call for water leak from AC system into bedroom. Upon arrival, inspected attic space and located clogged condensate drain line causing overflow. Cleared blockage from drain line using appropriate methods and verified proper drainage flow. Inspected surrounding insulation and structural components for water damage. Noted moisture evidence on wooden beam near drain pan area. Confirmed AC system operational with condensate draining properly through cleared line. System tested and no active leaking observed at time of departure.

Performed commercial HVAC coil cleaning service on two evaporator coils located in confined crawl space area. Coils exhibited significant dust and debris accumulation on aluminum fins, restricting airflow and reducing system efficiency. Thoroughly cleaned both coil assemblies, removing accumulated particulate matter from fin surfaces and surrounding ductwork to restore proper heat transfer capabilities and optimize unit performance.

Conducted comprehensive electrical assessment for standby generator installation at residential property. Evaluated existing 200-amp main electrical panel to determine compatibility and capacity for generator integration, documenting current circuit configuration and available breaker positions. Inspected natural gas service infrastructure, including existing gas meter and supply lines, to verify adequate fuel source capacity and pressure ratings for proposed generator unit. Photographed electrical panel interior showing circuit breaker arrangement and labeling, as well as exterior gas metering equipment to support load calculations and utility coordination requirements for generator hookup specifications.

Completed routine AC tune-up on attic-mounted air handler/gas furnace unit located above garage. Inspected and tested dual-run capacitor (TRCFD455, 440/370VAC), verified proper electrical connections and voltage readings at 227VAC, confirmed all compressor and fan motor circuits functioning within normal parameters. Customer provides their own filter for unit maintenance.

Completed sump pump discharge line reroute by capping the existing discharge line and core drilling a new 2" hole through the foundation wall just above ground level. Installed new 1½" PVC discharge pipe through the yard, trenched under the sidewalk near the home, and angled the line toward the far left side of the yard terminating at a pop-up emitter. Sealed the foundation wall penetration with hydraulic cement to prevent water infiltration and verified proper system function with no leaks before departure.

Responded to no cooling complaint on 12-year-old heat pump system. Upon inspection, diagnosed failed dual run capacitor (CAP050400440R1) on outdoor unit. Verified capacitor failure using clamp meter with amperage readings confirming compressor was not operating within normal parameters. Replaced defective capacitor and tested system operation. Unit restored to proper cooling function with compressor and condenser fan motor running at correct amperage. Customer advised that due to system age and presence of multiple units on property, they should anticipate potential replacement needs in the near future.

Performed preventive maintenance filter cleaning service on HVAC system with washable filters installed in the units. Removed and inspected reusable air filters which showed heavy accumulation of dust, debris, and particulate matter across the filter media surfaces. The filters displayed significant gray-white coating and uneven dust buildup that was restricting proper airflow. Documented pre-cleaning condition of filters through photographs showing the extent of contamination on the teal-colored filter media and metal frame assemblies. Completed cleaning procedure on washable filters per manufacturer specifications and returned filters to their respective unit housings. System equipped with permanent washable filters that remain installed in the units for ongoing use.

Completed comprehensive Care Plan tune-up on dual-zone HVAC system including ground floor air conditioning unit located in crawlspace, heat pump/air handler in attic, and outdoor condenser unit on rooftop with interior access. Performed full system diagnostics using clamp meter to verify electrical readings and amperage draws on all equipment, confirming proper operation at 29.10 amps on tested circuit. Replaced 20x20x1 air filter (X6670 model included in maintenance plan), inspected all accessible components, and documented equipment condition with diagnostic photos showing proper electrical values and clean equipment operation across all system zones.

Responded to no heat call on 5-year-old Bryant heat pump system that stopped producing warm air overnight. Upon arrival, performed diagnostic inspection of outdoor condenser unit and electrical components. Inspected capacitor and associated wiring connections, including red, purple, brown, and yellow wire terminals. Verified proper electrical connections to capacitor terminals and checked component condition. System evaluated and capacitor inspected for proper operation to restore heating functionality to the heat pump unit.

Responded to callback for recently installed A.O. Smith water heater with no hot water condition. Upon inspection, discovered the black power wire had been cut with insufficient length remaining to reconnect directly to the unit's electrical junction box. Wire will require extension to restore proper electrical connection and functionality to the water heater.

Completed preventative maintenance tune-up on two HVAC systems with gas furnace and air conditioning units located in crawl space as part of Club Duo care plan service. Inspected and serviced both Space-Gard high efficiency air cleaner units with customer-supplied 20x25x6 filters, verified proper installation of flexible ductwork connections, and examined refrigerant line connections showing normal wear and minor debris accumulation. All systems tested and operating within manufacturer specifications.

Completed annual Care Plan tune-up for air conditioning and gas furnace system located in crawlspace. Performed comprehensive inspection and maintenance of HVAC equipment, including temperature diagnostics showing 90.6°F readings at supply plenum. Customer provided filters (14x25x1) for replacement as part of routine maintenance protocol.