Top-Rated Plumbing in Lexington, KY

Responded to callback for 3rd floor geothermal unit experiencing intermittent cooling failure. Upon arrival, verified system operation and reviewed previous service notes indicating compressor monitor error code occurring after extended run times. Confirmed compressor jacket had been previously removed to improve heat dissipation. Monitored system through multiple cooling cycles while verifying refrigerant pressures, temperatures, and electrical parameters remained within manufacturer specifications. Cycled thermostat between cooling modes and observed proper system response with setpoint holding at 70°F. Unable to replicate compressor monitor fault code during this visit. System operating normally with adequate airflow and cooling capacity at time of departure.

Completed full residential HVAC system replacement including installation of Lennox 2.5 ton 14.3 SEER2 air conditioning unit (Model ML14KC1-030-230) and 90% efficiency gas furnace (Model ML193UH090XE36) with evaporator coil (Model CK40CT-30/36C-71). Repositioned furnace parallel to floor joists to facilitate easier filter access and maintenance. Fabricated and installed new supply and return plenums with integrated filter box. Ran new flexible ductwork from plenum to existing supply hard pipe connections. Installed outdoor condenser unit on concrete pad with electrical whip kit, disconnect box, and refrigerant line insulation. Added refrigerant line filter drier for system protection. Connected evaporator coil to existing ductwork with proper transitions. Installed SS2 coil drain safety water sensor for overflow protection. Fabricated transition to evaporator coil with standard-sized air filter rack. Connected furnace to existing flue piping with proper venting. Installed electrical sh

Completed full residential HVAC system installation featuring a RUUD 2-ton, up to 15.2 SEER2 two-stage heat pump (model RP14AY24AJ2NA) paired with RUUD air handler (model RH2TY2417STANNJ) and 10KW auxiliary heat kit (model RXBH-1724A10J-B). Installation included outdoor unit pad with snow legs, electrical whip kit, disconnect box, refrigerant line insulation, refrigerant line filter, digital thermostat, 20x20 return air filter grille, and condensate pump. Removed and disposed of existing equipment, pulled all applicable permits, installed complete refrigerant piping with proper insulation, established electrical connections to code, and verified system operation using digital manifold gauges to confirm proper refrigerant charge and system performance.

Responded to no cooling complaint on electric air conditioning system with reported freezing issue. Upon arrival, unit had been thawed and was operational. Performed diagnostic evaluation to determine root cause of freeze-up condition. Measured supply air temperature at 53.5°F at the ductwork, confirming system was cooling at time of inspection. Connected refrigerant manifold gauges to outdoor condensing unit to check system pressures and verify proper refrigerant charge. Conducted visual inspection of indoor and outdoor components. Based on diagnostics performed, system was operating within normal parameters at time of service, though previous freeze-up condition had occurred. Recommended monitoring system performance and checking air filter regularly to prevent restricted airflow, which is a common cause of evaporator coil freezing.

# HVAC Service Report Responded to no-cool call for 15-year-old residential air conditioning system affecting entire home. Upon arrival, accessed attic-mounted air handler unit and performed diagnostic evaluation. Inspected internal components including control board with digital display and air filtration system. Noted blue mesh filter showing signs of debris accumulation and discoloration. Examined circuit board connections, wiring harness, and electrical components for proper operation. Documented equipment condition and internal components with photographs for service records.

Responded to no cooling complaint on 4-year-old Carrier downstairs system. Performed diagnostic evaluation of indoor air handler and measured supply air temperature at 55.5°F. System had been providing adequate heating but failed to reach cooling setpoint. Inspected ductwork connections, refrigerant lines, and electrical components for proper operation and identified cooling system malfunction requiring correction.

Completed residential HVAC system installation including Bryant 148TAN04800W two-stage 4-ton condenser rated up to 18 SEER2, Bryant CVAVA4821XMA 4-ton evaporator coil, and Honeywell digital WiFi thermostat. Installed outdoor unit on protective pad against exterior brick wall with electrical whip kit, disconnect box, and proper refrigerant line insulation with filter drier. Replaced 14x14 flat return grille in return drop and completed transition from evaporator coil to existing ductwork. Installed SS2 coil drain safety water sensor for secondary drain pan protection. Secured all refrigerant lines and condensate drainage piping to building exterior with appropriate mounting brackets. Removed and disposed of existing equipment, obtained applicable permits, and verified system operation with successful startup and testing procedures.

Completed preventative maintenance tune-up on heat pump system located in attic as part of club membership care plan. Performed comprehensive system inspection including electrical testing with clamp meter showing proper amperage draw of 0.59A, verified capacitor operation and connections, and inspected all wiring and components for proper operation. Customer provided 16x25x1 filter for unit, all ductwork and electrical connections found secure and functioning within manufacturer specifications.

Completed comprehensive discharge line rerouting project involving capping the existing sewer discharge connection and installing a new discharge system. Routed new PVC discharge line across the basement ceiling, secured within floor joists, and extended to the front exterior wall. Drilled penetration through external wall and installed downward discharge into garden bed area left of front entrance. Trenched tunnel beneath concrete sidewalk to minimize surface disruption and ran discharge line approximately 6 feet into front yard, terminating at pop-up emitter for proper drainage dispersal. Ensured all connections were secure, tested system for proper flow and verified no leaks at any junction points prior to completion.

Completed scheduled electrical maintenance on Generac 24kW standby generator, serial number 3013806787. Performed comprehensive system inspection, verified proper operation of all components, and documented equipment condition with photographic records. Noted organic growth accumulation on exterior housing requiring future cleaning attention to maintain optimal ventilation and equipment longevity.

Completed preventive maintenance tune-up on heat pump and air handler system located in garage. Performed comprehensive inspection including temperature and humidity readings (43% RH recorded), verified proper airflow across evaporator coil and ductwork, and inspected outdoor condenser unit with operational fan assembly and electrical disconnect. All components found operating within normal parameters with customer providing their own filter replacements as requested.

Completed annual Care Plan tune-up on Trane heat pump and air handler system located in attic. Performed comprehensive maintenance inspection including checking thermostat operation (confirmed system holding at 72° and functioning properly), inspecting attic-mounted equipment, and verifying two 20x20x1 return filter grilles in ceiling. All system components operating within normal parameters at time of service.

Completed Care Plan tune-up on air conditioning and gas furnace system located in basement. Performed comprehensive maintenance inspection and testing of HVAC equipment. Measured and recorded system temperatures using digital thermometer, obtaining readings on ductwork and insulation surfaces to verify proper airflow and temperature differentials. Customer provided 16x25x1 air filters for installation during service. All maintenance procedures completed within customer's requested timeframe.

Completed full residential heat pump system installation in crawl space consisting of Bryant 2-ton 15 SEER2 single-stage outdoor heat pump unit (model GH5SAN52400A), Bryant air handler (model FJ5ANXA24L00), and 10KW auxiliary electric heat kit (model TU-EC-10BKB). Installed new digital thermostat for system control. Removed and properly disposed of existing HVAC equipment per environmental regulations. Installation included outdoor unit placement on new concrete pad with snow legs for elevation and proper drainage. Installed electrical disconnect box at outdoor unit location and electrical whip kit for code-compliant power connection. Ran insulated refrigerant line set between outdoor heat pump and indoor air handler with inline refrigerant filter for system protection. Applied proper insulation to all refrigerant lines to prevent condensation and maximize efficiency. Positioned air handler in crawl space with proper clearances for service access. Connected flexible silver insulated

Conducted electrical estimate for code compliance upgrades. Assessed existing outlet installations with metal boxes and documented electrical system conditions requiring updates to meet current electrical code standards. Collected customer contact information for follow-up estimate delivery.

Responded to no cooling call for 6-year-old Gibson air conditioning system. Upon arrival, verified system was not running and measured supply air temperature at floor register reading 77.5°F, confirming lack of cooling. Inspected outdoor condenser unit and found equipment in good physical condition with proper clearances from surrounding landscaping. Diagnosed issue, restored system to proper operation, and verified adequate airflow through floor registers.

Completed comprehensive Care Plan tune-up service on heat pump and air handler system located in attic space. Performed standard maintenance procedures including inspection of indoor air handler unit with ceiling-mounted return air grille, verified proper operation of all system components, and conducted exterior equipment assessment of heat pump condenser unit at foundation level. Customer provided replacement air filters as arranged, which were installed during service visit.

Completed installation of wooden access door with black metal hinges to cover HVAC system at exterior crawlspace entrance. Door was secured to concrete block foundation adjacent to vinyl siding, with latch mechanism installed for proper closure. Photographic documentation taken to verify completion of work that was originally scheduled as part of initial system installation.

Responded to no cooling complaint on 10+ year old Goodman gas furnace system with indoor unit located in basement. Upon arrival, determined issue was related to recent service visit. Diagnosed failed condenser fan motor on outdoor unit. Replaced defective condenser fan motor and verified proper electrical connections at control board. Tested system operation, confirmed adequate airflow across condenser coil, and verified unit cooling properly. System restored to normal operation.

Completed commercial HVAC system installation involving two complete 3-ton Trane heat pump systems. Installed two Trane model 5TWA403600A 3-ton 3-phase heat pumps, two Trane model 5TEM4B03AC31SA 3-ton air handlers, and two Trane model BAYHTR3510LUGC 10KW 3-phase heat kits. Utilized existing thermostats, equipment pads, disconnects, and electrical whips to minimize disruption and reduce installation time. Removed and properly disposed of all existing equipment per environmental regulations. Installed condensate drain lines with PVC fittings and proper insulation on refrigerant lines to prevent condensation issues. Configured ductwork connections in attic space using insulated flex duct and rigid duct components with foil-wrapped insulation for optimal thermal efficiency. All electrical connections completed to code specifications for 3-phase power supply. System startup performed on both units, verifying proper refrigerant charge, airflow, heating and cooling operation, and thermostat f