Top-Rated Heating, Cooling in Lexington, KY

Completed comprehensive plumbing inspection as part of preventative service agreement. Inspected water supply lines, including braided metal flexible hoses at fixture connections, and examined mechanical system plumbing components for proper operation, leaks, and signs of corrosion or wear.

Performed camera inspection of basement floor drain as requested by HVAC technician to diagnose drainage issue. Inspected drain line using video camera equipment, documented existing plumbing configuration including vertical PVC drain pipes with zip-tie securing and rubber boot penetration through floor assembly. Observed signs of moisture and debris accumulation around drain area, with visible wear and staining on surrounding surfaces indicating potential drainage concerns. Provided repair estimate based on camera inspection findings to address identified issues with drain system.

Responded to referral for toilet flange repair. Upon inspection, found existing flange severely corroded with extensive rust damage and structural deterioration throughout the component. Removed failed flange and replaced with new unit to restore proper toilet mounting surface and ensure leak-free seal.

Responded to warranty call for upstairs system failing to reach setpoint temperature. System thermostat set to 75°F but indoor temperature remaining at 79-80°F. Performed diagnostic testing using refrigerant analyzer, capturing system pressures and temperatures for R454B refrigerant. Measured suction and liquid line temperatures, superheat at 7.6°F, and subcooling at 8.3°F to verify proper refrigerant charge and system operation. Documented all readings and conditions with photos for warranty records. Discussed potential thermostat replacement with Honeywell Elite Pro WiFi model if temperature control issues persist after monitoring system performance.

Responded to water heater leak in utility closet where existing 2018 unit had discharged majority of tank contents. Removed failed water heater and installed new Bradford White tanked water heater. Connected all copper supply lines, installed new flexible gas connector, and verified proper venting. Tested all connections for leaks, confirmed proper ignition and burner operation, and verified hot water delivery to fixtures throughout home.

Completed Gold Level preventive maintenance on single HVAC system. Performed comprehensive system diagnostics including electrical testing and measurements, verified capacitor reading of 27.7 MFD, and documented equipment conditions per club maintenance protocol.

Converted existing 3-prong stove outlet to 4-prong configuration to accommodate newly purchased appliance. Installed black 4-prong receptacle supplied by company. Verified proper electrical connections at panel and ensured grounding compliance with current code requirements for range installation.

Completed full residential HVAC system installation featuring a Bryant Sentry Series 1.5 ton heat pump system with 14.3 SEER2 single stage outdoor unit (model GH5SAN51800A), indoor air handler (model FJ5ANXA18L00), and 10KW auxiliary heat kit. Removed and disposed of existing equipment per code compliance requirements. Installed outdoor condenser unit on concrete pad with snow legs, electrical disconnect box, and electrical whip connection. Mounted air handler with transition to existing ductwork and standard-sized air filter rack. Installed insulated refrigerant lines with refrigerant line filter connecting outdoor and indoor components. Added comprehensive drain safety system including trap, SS2 coil drain safety water sensor, and "Ceiling Saver" overflow drain pan with water sensor for secondary protection. Completed all electrical connections and secured refrigerant lines to exterior wall with mounting brackets. Installed digital thermostat for system control. Obtained applicable p

Responded to electrical service call for outlet work in interior utility space. Upon arrival, assessed existing electrical infrastructure in area showing significant wall damage and deterioration. Evaluated exposed wiring and existing outlet configurations on damaged drywall surfaces. Documented pre-existing conditions including compromised wall surfaces, exposed conduit, and deteriorated flooring materials that required consideration for safe electrical installation. Verified electrical connections and mounting locations for outlet installations, ensuring proper clearances and code compliance despite challenging wall conditions. Completed photographic documentation of work area before and during service for quality assurance and safety records.

Responded to no cooling complaint on 10+ year old electric upstairs AC unit with reported no airflow. Upon arrival, performed system diagnostics and inspection of both indoor and outdoor equipment. Discovered outdoor condenser unit experiencing significant operational issues. Inspection revealed extensive corrosion and oxidation on refrigerant line set, including copper suction line showing advanced deterioration with rust-colored and greenish patina buildup. Condenser fan motor housing showed signs of age and weathering. Corroded refrigerant lines compromised system integrity and likely contributing to loss of cooling capacity and airflow issues. Documented equipment condition with photographic evidence showing deteriorated copper piping, corroded components, and aging outdoor unit assembly. Given the age of the system and extent of component deterioration, provided assessment and repair options to restore cooling function.

Completed second maintenance visit on commercial facility with eleven HVAC systems including ten standard units and one Mitsubishi ceiling cassette mini-split. Performed comprehensive preventive maintenance on all systems including inspection of electrical connections, refrigerant pressures, condensate drainage, and operational controls. Replaced disposable pleated filters on seven units with specified sizes: one 20x20x1, three 13x21.5x1, one 16.5x21.5x1, and two 19.5x21.5x1. Cleaned and reinstalled washable filters on four Bryant units and the Mitsubishi ceiling cassette unit. Verified temperature differentials across evaporator coils, inspected copper refrigerant lines and heat exchanger fins, and tested all safety controls and thermostats for proper operation. All systems found operating within normal parameters with no deficiencies noted.

Performed routine maintenance flush on a 2-year-old Rinnai gas tankless water heater located in the utility room. Isolated the unit using the installed shut-off valves on the inlet and outlet PEX lines, connected flushing equipment, and circulated descaling solution through the heat exchanger to remove mineral buildup and sediment accumulation. Verified proper operation of the unit upon completion, confirmed temperature display functionality, and ensured all connections were secure with no leaks detected.

Responded to no power condition at residential property where utility company confirmed power present at meter. Upon arrival, inspected electrical system and determined issue was related to Generac Guardian 16kW backup generator transfer system. Examined transfer switch panel and associated components including Siemens main breaker and control module with AC circuit indicators. Diagnosed malfunction in automatic transfer switch preventing proper power distribution from utility source to home circuits. Restored full power to residence by addressing transfer switch operation and verifying all circuits functioning properly.

Completed comprehensive electrical estimate for natural gas generator installation at residential property. Assessed existing utility room infrastructure, including mechanical systems, plumbing assemblies, and electrical panel configuration to determine optimal generator placement and integration requirements. Evaluated electrical service capacity and identified appropriate location for dedicated circuit breaker installation to support generator connection. Documented current equipment layout featuring HVAC components, water heating system, and existing electrical distribution panel with available capacity for new generator circuit. Determined electrical load requirements and verified compatibility with natural gas fuel source for seamless emergency power system integration.

Responded to no cooling call on one-year-old electric HVAC system with flashing thermostat alert. Accessed indoor unit located in crawlspace to perform diagnostic inspection. Evaluated system components including flexible ductwork, refrigerant lines, electrical connections, and air handler assembly. Documented system configuration and current operating conditions through visual inspection of installation, including duct connections, insulation placement, and mechanical components mounted in crawlspace environment.

Relocated gas line for stove installation by rerouting the supply line into the wall cavity for a cleaner, code-compliant finish. Cut access opening in drywall to expose wall studs, installed flexible gas connector (CSST) through wall framing and secured routing through ceiling joists in attic space using proper support straps, then concealed piping within wall structure to eliminate exposed gas line from kitchen area.

Completed routine maintenance on heat pump and air handler system located in crawl space with washable filters. Accessed equipment through exterior crawl space entry point, navigated debris and vegetation to reach unit. Performed diagnostic testing using digital multimeter to verify electrical readings on compressor assembly, capacitors, and control board components. Inspected internal wiring connections, circuit board, and induction coils. All electrical measurements within normal operating parameters. System operating properly upon completion of maintenance inspection.

Completed sewer line restrap in crawl space beneath bathroom area. Two-person crew accessed underfloor space, repositioned and secured existing PVC sewer line with proper strapping and support to eliminate sagging and ensure adequate drainage slope. Work performed during requested 10-12 time window.

Completed comprehensive plumbing inspection of under-sink fixtures and drainage system. Examined supply line connections, shut-off valves, flexible hoses, PVC drain assembly with threaded fittings, and verified proper installation of all plumbing components with no leaks or deficiencies observed at time of inspection.

Completed comprehensive AC tune-up and preventive maintenance on a five-year-old split HVAC system with furnace located in crawlspace and air handler in attic. Performed electrical diagnostics using multimeter to verify proper voltage and amperage readings at blower motor, gas valve assembly, and control board connections. Inspected all internal wiring connections including red, purple, orange, yellow, white, and black wire terminals for secure contact and signs of wear. Tested and calibrated Honeywell Home ProSeries digital thermostat, confirmed cooling mode operation set at 73 degrees with fan on auto mode and verified proper communication between thermostat and system. All equipment operating within manufacturer specifications with no issues identified during inspection.