Top-Rated Heating, Cooling in Lexington, KY

Completed comprehensive maintenance tune-up on three ground floor air conditioning systems as part of club membership care plan. Performed detailed inspection of all three units, documenting equipment conditions including capacitors, burner assemblies, gas valves, electrical connections, and control components. Observed normal operational wear and dust accumulation on mechanical components; all systems inspected and serviced according to manufacturer specifications to ensure optimal performance for continued operation.

Completed Gold Level prepaid maintenance on a single-system residential HVAC installation. Inspected Carrier furnace/air handler unit located in basement utility area and outdoor condensing unit (Model CNPVP4221ALAAAA, Serial 1713X18113) containing R-410A refrigerant. Provided and installed customer-supplied air filter #413 as part of membership benefits during spring maintenance visit. Verified all manufacturer specification labels, safety warnings, and refrigerant information were legible and intact on both indoor and outdoor equipment. Documented equipment condition through photographs showing ductwork connections, humidifier attachment, electrical wiring, and overall system operation.

Completed annual Care Plan tune-up on residential air conditioning system, including outdoor condenser unit inspection with electrical component verification and temperature diagnostics. Replaced 16x25x4 air filter in basement as part of club membership maintenance service.

Responded to water leak concern at attic-mounted indoor HVAC unit. Upon inspection, identified condensate drainage issue occurring during cooling operation on warmer days. Accessed attic via interior stairs and examined air handler, condensate drain line, and surrounding ductwork. Found condensate line experiencing drainage restriction, causing overflow during high-humidity cooling cycles. Cleared blockage from drain line and verified proper drainage flow. Inspected insulation for water damage and confirmed air handler drain pan functioning correctly. System tested under cooling operation with no further leakage observed.

Completed preventive maintenance tune-up on dual HVAC systems located in attic and basement as part of care plan agreement. Performed comprehensive system inspections including electrical diagnostics with multimeter, temperature differential measurements, and filter replacements with customer-supplied 14x20x1 filters. Both gas furnace and air conditioning units tested and confirmed operating within manufacturer specifications.

Responded to a leaking pipe issue in a seventy-year-old residential property. Upon arrival, conducted a thorough inspection of the plumbing system in the basement and attic utility areas. Located the source of the leak affecting a section of aging cast iron pipe that showed significant deterioration and corrosion consistent with the age of the home's original plumbing infrastructure. Assessed the existing pipe configuration, which included a combination of older black iron piping and newer PVC connections. The leak originated from a compromised section where metal pipe showed advanced weathering and structural weakness. Evaluated the extent of water damage and determined the necessary repair scope to prevent further issues. Documented the plumbing layout including horizontal drain lines, vertical risers, and connection points between dissimilar pipe materials. Photographed the affected areas showing the relationship between the cast iron sections, PVC transitions, metal couplings, an

# HVAC Service Call - No Cooling Condition Responded to service call for 9-year-old residential air conditioning system with complete loss of cooling and heating functionality. Customer reported outdoor AC unit not operational. ## Diagnostic Procedures Upon arrival, performed comprehensive system evaluation beginning with thermostat functionality check. Confirmed Trane thermostat displaying 77°F and verified proper power supply to control board. Tested thermostat communication with system components and confirmed display responding to input commands. Proceeded to outdoor condensing unit inspection. Conducted visual assessment of compressor, condenser fan motor, and electrical connections. Verified power supply at disconnect and measured voltage at contactor. Tested capacitor values using multimeter to determine if dual-run capacitor within acceptable microfarad range. Accessed attic-mounted air handler unit for indoor component evaluation. Inspected blower motor operation, evapora

Completed comprehensive Care Plan tune-up maintenance on four heat pump units and four air handler systems. Performed standard preventive maintenance procedures including inspection of electrical components, capacitors, and control wiring on all units, with customer providing their own filters for the systems.

Completed installation of 22KW Generac air-cooled standby generator with 200-amp automatic transfer switch equipped with surge protective device (SPD). Established all electrical connections between the generator, transfer switch, and main service panel, ensuring proper wire sizing and termination per NEC requirements. Performed system startup, load testing, and verified automatic transfer operation to confirm seamless power transition during utility outage conditions.

Completed installation of new sink drain assembly by drilling fresh hole in sink basin and installing chrome drain strainer with basket fitting. Connected white PVC P-trap configuration to new drain outlet and routed horizontal waste line to existing plumbing system. Installed new vent pipe running from drain assembly through cabinet and up through ceiling into basement area, ensuring proper drainage and venting per code requirements. All connections secured with appropriate fittings and tested for leaks. Verified proper drainage flow and vent function upon completion.

Completed warranty compressor replacement on commercial rooftop packaged HVAC unit over a three-day period. Recovered refrigerant, removed failed compressor, and performed comprehensive system flush from multiple access points to remove contaminants. Installed new compressor with new filter driers, conducted pressure test, and pulled overnight vacuum to ensure system integrity. Recharged system and monitored operation, then performed secondary refrigerant recovery, additional system flush, and filter drier replacement to ensure complete contamination removal. Completed final evacuation, recharged system to manufacturer specifications, and verified proper operation. Cleaned cabinet interior and collector box as part of warranty repair protocol.

Completed routine maintenance inspection on Club Trio system consisting of one packaged geothermal unit, one split geothermal system, and one mini-split system located in basement, attic, and sunroom. Performed temperature diagnostics on evaporator coil, recording 42.4°F with proper condensation present, and verified system pressures at zero static conditions using calibration gauge, confirming all three units are operating within manufacturer specifications.

Completed comprehensive care plan maintenance on a 5-year-old heat pump and gas furnace system with the furnace located in the basement. Performed standard tune-up procedures including inspection of the evaporator coil, which showed significant frost accumulation indicating proper refrigerant operation, and verified gas furnace combustion with all four burners igniting properly and producing clean blue flames. Inspected blower motor assembly, electrical connections, and control wiring; all components found to be functioning within normal operating parameters.

Completed residential mini-split changeout by installing Mitsubishi 18K BTU system (models MSZ-WX18NL indoor wall mount unit and MUZ-WX18NL outdoor condensing unit). Utilized existing refrigerant line set to connect indoor and outdoor components. Mounted outdoor unit on pad against exterior wall with proper electrical disconnect box and conduit installation, while indoor wall-mounted air handler was installed in bedroom location. Applied all necessary permits, removed and disposed of existing equipment, and installed electrical whip kit with disconnect box for code compliance. System tested and operational with heating capacity down to -14°F minimum operating temperature.

Responded to no heat call for third floor gas furnace unit failing to reach thermostat setpoint of 65°F, with actual temperature reading 58°F. Accessed attic-mounted HVAC system and performed diagnostic evaluation of furnace operation, inspected gas supply, electrical connections, and ductwork configuration. Unit was found operational with adequate airflow through flexible duct system, and system components were verified for proper function to restore heating capacity to occupied space.

Responded to no cooling call on electric HVAC system with indoor unit located in basement. Upon inspection, discovered failed contactor relay with severe heat damage, corrosion, and charring around terminals and mounting area. Evidence of electrical arcing and thermal deterioration indicated component failure preventing compressor operation. Replaced defective contactor relay, verified all wire connections secure, and tested system operation. Unit cooling properly upon departure.

Replaced underground electrical cable for outdoor water fountain pump by fishing new wire through existing conduit path. Successfully routed cable from fountain location to existing outdoor outlet without requiring interior home access. Verified proper connection and functionality of new wiring installation for fountain pump operation.

Responded to callback for non-operational HVAC system after multiple previous service visits. Upon inspection, discovered severe mold and debris contamination throughout blower assembly and air handler cabinet, which was causing system failure. Performed electrical diagnostics at breaker panel to verify power supply and circuit integrity. Documented extensive contamination on blower wheel and surrounding components requiring immediate attention. Recommended complete system cleaning and possible blower assembly replacement due to excessive buildup preventing proper airflow and operation.

Completed evaporator coil replacement on attic-mounted HVAC system. Pumped down existing refrigerant into compressor, removed failed coil, and installed larger replacement unit. Performed pressure test to verify system integrity, evacuated to manufacturer specifications, and recharged with R-410A refrigerant to proper levels.

Completed routine AC tune-up maintenance on two residential HVAC systems. Performed comprehensive diagnostics including capacitor testing and electrical measurements, with readings of 494 and 4.4 microfarads recorded using calibrated testing equipment. All systems inspected, tested, and found to be operating within normal parameters.