Top-Rated Heating, Cooling in Lexington, KY

Disconnected sump pump discharge line from the sanitary sewer system to bring installation into compliance with code requirements. Cored a penetration through the foundation wall and installed approximately 15 feet of PVC discharge piping extending from the basement to the backyard discharge point. Excavated trench through existing brick pathway in backyard, removed necessary pavers to accommodate underground piping, and routed discharge line away from the foundation to proper termination point. Installed new interior PVC piping with proper fittings and connections to redirect sump pump flow through the foundation wall. Backfilled excavated areas and reset brick pavers along pathway to restore access, prioritizing functionality of the discharge system.

Completed comprehensive spring Care Plan tune-up service on two air conditioning systems. Performed preventive maintenance inspections on both units, replaced 20x25x1 standard filter and Honeywell 20x25 media filter per plan specifications, verified proper operation of condensate safety switches, and inspected all ductwork, refrigerant lines, electrical connections, and capacitors to ensure optimal system performance for the cooling season.

Completed spring maintenance tune-up on 7-year-old residential HVAC system. Inspected attic condensate drain lines and verified proper configuration, checked outdoor condenser unit operation, and performed electrical diagnostics including capacitor testing with readings of 35.02 µF. All components operating within normal parameters.

Removed existing toilet and installed customer-supplied American Standard Champion ADA-compliant elongated bowl model. Completed installation with proper sealing, water supply connection, and tested for leaks and proper flushing operation.

Removed existing toilet and installed new extra tall assisted-flush premium toilet in bathroom with green accent wall. Installation included new mounting bolts, wax ring seal, and braided supply line to ensure proper function and prevent leaks.

Completed comprehensive AC tune-up on 2-year-old air conditioning system as part of scheduled care plan maintenance visit. Performed thorough electrical diagnostics using digital multimeter, recording voltage reading of 23.81V at contactor and relay components to verify proper electrical operation. Conducted temperature measurements with infrared thermometer on refrigerant lines, documenting suction line temperature at 49.1°F to assess system performance and refrigerant charge levels. Inspected all electrical connections, wire bundles, and contactors for signs of wear or damage. System operating within normal parameters with no deficiencies noted at time of service.

Responded to water leak originating from exterior hose bib penetrating into crawlspace. Upon inspection, identified leaking outdoor spigot mounted on brick exterior wall with compromised connections allowing water infiltration through wall penetration into crawlspace area. Observed moisture presence in crawlspace affecting floor joists, fiberglass insulation, and concrete block foundation wall. Repaired/replaced hose bib connections and fittings to eliminate active leak. Verified proper seal at wall penetration point to prevent future water intrusion into crawlspace. System tested and confirmed watertight operation upon completion.

Completed Gold Level preventative maintenance tune-up on single-system HVAC including gas furnace, air conditioning unit, and humidifier. Performed comprehensive system inspection, verified thermostat and Aprilaire humidity control operation at 76°F, conducted electrical diagnostics with clamp meter to confirm proper amperage draw, replaced humidifier pad #35 per maintenance schedule, and documented that customer will provide their own air filter.

Completed comprehensive care plan tune-up on a 20+ year old heat pump and air handler system located in closet. Performed standard maintenance protocol including inspection of exterior condensing unit, verification of refrigerant lines, and temperature diagnostics of ductwork system. Customer provided filters for installation as part of routine maintenance. All components inspected and system operational upon completion.

Responded to a water leak under the kitchen sink caused by separated PVC drain pipes in the dual-basin assembly. Reconnected the disconnected drain pipes, secured all connections, and tested the system to ensure proper drainage without leakage. Restored full functionality to the sink and dishwasher drain system.

Completed preventive maintenance tune-up on air conditioning system and gas furnace unit located in basement at bottom of steps. Performed comprehensive electrical diagnostics using clamp meter to verify system amperage draw, recording 50 AAC on primary circuit and additional measurements on secondary components. Inspected capacitor and electrical connections, noting all wiring intact with proper terminations. Observed 16x25x1 filter supplied by customer. All electrical measurements within manufacturer specifications, system operating normally upon completion of service.

Completed Gold Level prepaid maintenance on single-zone residential air conditioning system with gas furnace located in lower level closet. Performed comprehensive inspection of indoor and outdoor units, replaced customer-provided 16x25x1 air filter, checked electrical connections and capacitor at condenser unit, verified refrigerant pressures using manifold gauges, and documented system condition with photos. All components operating within normal parameters upon completion.

Performed comprehensive maintenance service on Bradford White 40-gallon natural gas water heater, model RG240T6N. Completed full tank drain and flush to remove sediment buildup, as unit had never received previous maintenance despite being in working condition. Inspected and evaluated anode rod condition for potential replacement needs. Examined venting system extending into attic area and assessed condition of vent connector and proper clearance specifications. Verified all plumbing connections, including copper supply lines and flexible gas line connections, for proper operation. Unit operational upon completion of maintenance service.

Completed Care Plan tune-up on gas furnace and air conditioning system located in basement. Performed comprehensive system inspection, checked thermostat settings per customer request, and investigated reported loud blower noise that has been present since installation. Utilized Fluke 323 True RMS Clamp Meter to verify electrical readings and test capacitor function. Customer provided replacement air filter which was inspected and documented.

# Plumbing Estimate - Drain Line Replacement Conducted comprehensive assessment of residential drain system requiring replacement of multiple fixtures and drain lines. Inspection revealed toilet drain line extending approximately 4 feet to main sewer connection required complete replacement due to deterioration or damage. Additionally, bathtub drain and overflow assembly needed replacement, along with the associated drain line running from tub to main sewer line. Accessed crawl space and attic areas to evaluate existing plumbing infrastructure. Documented current conditions of cast iron and PVC drain piping, including T-joint connections and horizontal drain runs. Examined structural wooden joists and clearances for new pipe installation. Identified routing path for replacement drain lines through floor framing system while maintaining proper slope and code-compliant venting. Assessment included evaluation of connection points at main sewer line, verification of pipe sizing requirem

Completed routine AC tune-up on 7-year-old air conditioning system during scheduled maintenance visit. Performed comprehensive system inspection including visual assessment of furnace and mechanical equipment in basement, verified proper air filter installation, and conducted electrical diagnostics on outdoor condensing unit using clamp meter to measure amperage draw and confirm system is operating within manufacturer specifications. All components found to be functioning properly with no issues identified requiring immediate attention.

Completed planned maintenance service on Bryant heat pump system located in loft area above offices. Performed comprehensive fall maintenance inspection including temperature diagnostics on supply ductwork, recording 69.0°F at duct surface using calibrated digital thermometer. Inspected insulated ductwork in attic space for proper wrapping and thermal integrity. Conducted exterior inspection of condenser unit, verifying proper installation on concrete pad, checking electrical disconnect, refrigerant line connections, and overall unit condition. System operating within normal parameters with no issues identified during maintenance visit.

Responded to service call for downstairs HVAC system not operating with E1 error code displaying on thermostat. Inspected control board and electrical connections in basement air handler unit. Verified all wire terminations secure at terminal blocks, checked capacitors and control circuitry for proper operation. Documented control board configuration and wiring connections. System evaluated for any correlation to recent service work performed at property.

Investigated temperature discrepancy on existing Honeywell thermostat displaying 76°F while set to 72°F. After diagnosing the issue, removed the old thermostat and installed two new Ecobee smart thermostats to resolve the temperature control problem and provide improved system performance.

Completed comprehensive preventive maintenance tune-up on dual HVAC system consisting of two heat pumps and two air handlers as part of Care Plan service. Performed electrical diagnostics using calibrated testing equipment, measuring amperage at 26.7A and voltage at 24.65VAC to verify proper system operation and component functionality. Inspected capacitors, relay boards, electrical connections, and condenser coils on both outdoor units to ensure optimal performance and system reliability.