Top-Rated Heating, Cooling in Lexington, KY

Completed maintenance tune-up on heat pump system for new homeowner. Performed comprehensive inspection of outdoor condenser unit and indoor air handler located in kitchen closet, documenting equipment condition with diagnostic measurements showing 31.37 amp draw. System had never been serviced prior to this visit.

Rerouted existing sump pump discharge line from basement to front yard to address severe moisture damage and water infiltration issues evident along foundation walls. Installed new discharge piping terminating with pop-up emitter in front yard to properly divert water away from structure and prevent further basement flooding and foundation deterioration.

Responded to service call for guest bathroom toilet running constantly. Upon inspection, identified faulty flush valve and fill valve components with visible mineral buildup affecting proper operation. Removed tank lid and assessed internal mechanisms, noting deteriorated flapper seal and compromised fill valve causing continuous water flow. Recommended replacement of flush valve assembly and fill valve to restore proper function and prevent water waste.

Completed comprehensive Care Plan tune-up on dual-zone system including heat pump unit located in basement and mini-split system on third floor. Performed full inspection of gas furnace burner assembly, confirmed proper ignition sequence and flame characteristics with all burners operating efficiently, verified heat exchanger integrity, inspected gas valve operation and electrical connections, and installed 14x25x1 filter as included in Care Plan maintenance. All equipment tested and operating within manufacturer specifications.

Completed comprehensive Care Plan maintenance on Bryant HVAC system including air conditioning unit, gas furnace, and humidifier located in basement with access through garage. Performed full system inspection and tune-up procedures on all components, verified proper operation of air handler unit, inspected ductwork connections and insulation integrity, and replaced customer-supplied 16x20x4 Honeywell Home FC100A1003 air filter. All equipment tested and operating within manufacturer specifications upon completion.

Completed full residential HVAC system installation featuring a RUUD 14.3 SEER2 2.5-ton two-stage heat pump (model RP14AY30AJ2NA), RUUD air handler (model RH2TY3617STANNJ), and RUUD 15KW heat kit (model RXBH-1724A15J-B). Installed Honeywell digital WiFi thermostat for remote system control and monitoring. Modified return air system by installing 16-inch metal elbow and 20x25 return filter grille to ensure proper airflow for optimal system performance. Outdoor unit installation included placement on equipment pad with snow legs for elevation and drainage, electrical whip kit for flexible connection, and electrical disconnect box with interlock safety feature mounted to building exterior. Refrigerant lines were insulated and properly secured between outdoor condenser and indoor air handler. System was charged with 14.75 pounds of refrigerant as verified by digital scale measurement. Indoor air handler installation incorporated SS2 coil drain safety water sensor, "Ceiling Saver" overflo

Completed comprehensive care plan tune-up on heat pump and air handler system located in crawlspace. Performed full system inspection and maintenance procedures, verified proper operation of Honeywell Home ProSeries WiFi thermostat displaying cooling mode at 73°F setpoint, and confirmed functionality of REME-HALO Zero air purification system with eGHP-Cell technology. Customer advised that return air filters in sizes 20x30x1 and 14x20x1 are not included in maintenance plan and should be replaced as needed.

Rerouted two sump pump discharge lines approximately 10 feet away from the foundation wall to prevent water from pooling near the structure. Installed new PVC drainage piping extending from the existing sump pump outlets through the basement area and terminating with pop-up emitters in the yard for proper water dispersal. All work completed with materials and labor as specified, ensuring adequate drainage away from the building foundation to protect against water intrusion and foundation damage.

Responded to callback for geothermal system with two attic-mounted air handlers experiencing intermittent operation. Performed electrical diagnostics on control board of master bedroom zone unit that required manual resets to restore operation. Verified voltage readings at control panel and tested system components with multimeter to identify intermittent control issue. Removed all programmed schedules from Nest thermostats per customer request to eliminate unwanted temperature setpoint changes. Both zones tested and operational at time of departure.

Addressed failed inspection items on gas tankless water heater installation. Rerouted temperature and pressure relief valve discharge line to exterior using proper CPVC piping per code requirements. Relocated condensate drain line to terminate outside the building, replacing non-compliant PE tubing with code-approved CPVC material where stubbed through exterior wall.

Completed seasonal maintenance tune-up on 14-year-old outdoor condensing unit and basement air handler system. Performed refrigerant pressure diagnostics using manifold gauges, recording system pressures and electrical readings with digital multimeter to verify proper operating parameters. All equipment inspected and tested, confirming system operational within manufacturer specifications.

Completed commercial HVAC repair utilizing a two-person crew over four hours. Installed 50 feet of 18/8 thermostat wire and 50 feet of liquid-tight conduit to restore proper system communication and protect electrical components from environmental exposure. Documentation photos captured exterior building conditions, electrical meter installations, and HVAC condenser unit positioning to verify completed work and system accessibility.

Completed preventative maintenance tune-up on dual heat pump/air handler system located in closet and attic as part of annual care plan service. Performed comprehensive inspection of electrical components including contactors, capacitors, and wiring connections on both units; verified proper voltage readings and amperage draws within manufacturer specifications. All system components found operating normally with no deficiencies noted at time of service.

Accessed outdoor HVAC unit via rear pool entrance and successfully replaced failed capacitor to restore system operation. Documented existing equipment configuration and obtained detailed measurements and photographs of Unit #3 for upcoming system replacement quote, including assessment of outdoor condensing units and indoor mechanical systems.

Completed routine plumbing inspection of residential bathroom fixtures. Tested water flow and pressure at sink faucet and shower system, verified proper operation of all valves and controls, and confirmed no visible leaks or drainage issues. All fixtures found to be functioning properly with adequate water pressure and temperature control.

Completed scheduled care plan tune-up on heat pump and air handler system located in attic. During inspection, discovered severely compromised condensate drain line with visible vertical crack and deterioration requiring immediate attention to prevent water damage and system shutdown. Documented damaged PVC piping showing structural failure and discoloration, which posed risk of condensate overflow. Performed standard maintenance protocol including system operational checks, component inspection, and photographic documentation of deficient plumbing conditions for customer awareness and future repair coordination.

Completed scheduled HVAC maintenance on basement AC/gas furnace unit. Performed system diagnostics using digital multimeter, recording voltage readings of 229V and verifying electrical components operating within normal parameters. Measured supply air temperature at 43.3°F, confirming proper cooling performance. Inspected ductwork, gas line connections, and wiring harness for proper installation and secure connections. All system components found in satisfactory working condition. Customer provided 16x20x1 filter for installation.

Completed comprehensive care plan tune-up on heat pump and air handler system located in attic space. Performed seasonal maintenance including switching damper positions at each multi-zone unit for optimal airflow distribution. Verified electrical performance using diagnostic meter, confirming proper amperage draw at outdoor condenser unit. Inspected evaporator coil assembly, noting V-configuration coil construction with clean aluminum fins and proper alignment throughout both sections.

Responded to service call for assessment of water heater venting system flagged by inspector as undersized for the installed unit. Upon arrival, inspected A.O. Smith ProLine Commercial Grade tanked water heater located in second-floor utility closet, approximately one year old and in otherwise good operating condition. Conducted thorough evaluation of existing venting configuration, including measurement and documentation of current vent pipe diameter and routing. Utilized digital level to verify proper pitch and alignment of exhaust vent system. Examined the galvanized metal flue pipe extending from top of unit, including elbow joint and connection points secured with metal bands. Assessed clearances, combustion air supply, and overall installation compliance with manufacturer specifications and current building codes. Confirmed inspector's findings that existing vent pipe diameter does not meet required specifications for this commercial-grade water heater model. Documented install

Responded to service call for toilet requiring internal component replacement. Upon arrival, inspected residential toilet in powder room with standard two-piece configuration. Assessed existing flush valve and fill valve assembly for wear and malfunction. Replaced complete toilet tank internal components including flapper, flush valve, fill valve, and associated hardware. Tested flush mechanism for proper operation, verified water level adjustment, and checked for leaks at all connection points. Confirmed toilet restored to full working order with proper flushing and refill cycle.