Plumbing, Electric and HVAC Services in Georgetown, KY

Corrected and secured wall flange assembly at exhaust pipe penetration point to eliminate gaps between the metal flashing plate and wall surface. Installed proper sealing components to ensure a professional, weathertight installation where the exhaust pipe exits through the exterior wall.

Responded to non-urgent service call regarding loose and improperly installed upper furnace flue pipe with inadequate drywall clearance identified during pre-sale home inspection. Upon arrival, assessed the B-vent or metal flue pipe penetration through the wall assembly and confirmed insufficient clearance between the vent pipe and combustible drywall materials, creating a code violation and potential safety hazard. Measured existing clearances and documented deficiencies with the wall thimble installation. Corrected the flue pipe positioning by properly seating the vent pipe into the wall-mounted metal flange assembly, ensuring the pipe was fully engaged and secured within the thimble. Verified proper clearances were maintained between the vent pipe and all combustible materials per manufacturer specifications and local building codes. Confirmed the flue pipe connection was stable and properly aligned for safe exhaust venting from the furnace system.

Completed Gold Care Plan Tune Up on residential HVAC system. Performed comprehensive system diagnostics including electrical measurements using clamp meter, which indicated 10.4 amp draw on compressor circuit. Inspected all major components including capacitor, wiring connections, and control board—all found to be in proper working condition. Verified thermostat operation and confirmed system settings with unit in off mode and fan set to auto at 65 degrees.

Completed annual maintenance tune-up on geothermal HVAC system with one ground loop and humidifier located in basement. Performed comprehensive inspection including electrical testing of system components, verified loop pressures on GEOLINK hydronic heating system and dual circulation pumps, inspected ground loop manifold assembly and connections, checked #35 pad and washable filter, and documented system operation with all parameters within normal operating range.

Replaced failed blower motor on upstairs air handling unit to restore proper airflow and system operation. Repaired leaking condensate drain line by replacing damaged PVC sections and fittings, ensuring proper drainage and preventing water damage to surrounding areas.

Completed annual care plan maintenance on single-zone HVAC system consisting of one heat pump and one air handler. Performed comprehensive tune-up including inspection of electrical components, contactors, relays, and capacitor at outdoor unit, verified all wire connections and terminals were secure, replaced 16x20x1 air filter at indoor air handler, inspected blower motor and housing, examined refrigerant lines and control wiring harness, and documented equipment condition with photos of electrical panel and furnace interior components.

Conducted electrical estimate for panel expansion and 150-foot electrical run from existing service panel to poolside deck area to supply power for gazebo, automatic pool cover, and pool heater. Assessed current 200-amp residential electrical service panel mounted on exterior wall with adequate capacity for additional circuits. Evaluated crawl space routing for underground conduit run, noting accessible path through foundation area with proper clearances from HVAC ductwork and structural supports for code-compliant installation.

Performed comprehensive air conditioning tune-up and routine maintenance on basement-located AC system. Inspected and verified proper operation of dual-run capacitor (45+5 MFD, 440/370 VAC) with all terminals securely connected, examined refrigerant sight glass showing appropriate charge levels with green indicator fluid, and documented system conditions through photographic records. Noted 20x25x4 filter size for replacement during scheduled fall visit.

Replaced worn bathtub drain stopper lever assembly due to failed linkage mechanism. Removed corroded original assembly including trip lever, linkage rod, and spring components, then installed new lever assembly to restore proper stopper operation.

Completed comprehensive care plan maintenance on two gas furnaces and one air conditioning unit. Primary furnace system located in basement area, secondary furnace in washroom area with no associated cooling equipment. Performed full seasonal tune-up procedures including inspection of burner assembly, ignition components, heat exchanger, and gas valve operations. Verified proper thermostat operation and calibration on Honeywell digital control. Checked all electrical connections, tested safety controls, and inspected copper refrigerant lines on AC unit. Customer provided 16x25x1 air filters for installation. All systems operating within manufacturer specifications upon completion.

Completed comprehensive Care Plan tune-up on heat pump and air handler system located in attic. Performed diagnostic testing on outdoor condenser unit using digital multimeter to verify electrical performance and system operation. Inspected internal electrical components, wiring connections, and refrigerant line system including copper tubing and service lines. Provided additional air filters as requested (16x25x1 and 20x25x4 sizes) to supplement customer-supplied filters for ongoing maintenance.

Completed comprehensive Care Plan tune-up service on an 8-year-old heat pump system with air handler located in attic. Performed full system diagnostics including electrical testing at outdoor condenser unit, verified thermostat operation and programming, inspected both indoor and outdoor equipment components, and confirmed proper system performance per manufacturer specifications.

Responded to service call for non-operational 15-year-old geothermal air conditioning system with reported blower fan failure. Coordinated gate access call prior to arrival for evening appointment window. Upon inspection, accessed attic-mounted air handler unit and assessed system components including condensate drainage lines and refrigerant piping connections. Documented existing equipment condition showing age-appropriate wear, moisture accumulation on insulated refrigerant lines, and water staining around condensate connections indicating previous drainage activity. Photographed air handler installation, ductwork connections, electrical wiring, and PVC condensate drain routing for service records. Evaluated blower motor operation, electrical supply to unit, and overall system functionality to diagnose reported cooling failure and determine necessary repairs for geothermal heat pump system.

Performed routine maintenance on 2024 heat pump system with attic-mounted air handler. Conducted electrical diagnostics on outdoor condensing unit using clamp meter, verifying amperage draw at 0.56 amps, and inspected dual-run capacitor rated at 35/5µF for proper operation. Confirmed thermostat functionality showing system maintaining 70°F indoor temperature with 27% humidity and verified heating and cooling setpoints programmed correctly.

Responded to water leak investigation call at residential bathroom. Conducted thorough inspection of shower enclosure and bathtub area featuring marble-tiled walls and frameless glass panels. Located source of water intrusion and documented findings with photographic evidence. Identified leak origin point and explained repair requirements to customer for future remediation work.

Responded to service call for two non-functioning electric water heaters in older home, each on separate electrical disconnect boxes. Inspected both exterior-mounted disconnect switches and verified breakers were not tripping. Found deteriorated wiring connections and corroded terminals in both disconnect boxes due to age and environmental exposure. Cleaned terminal connections, replaced damaged wire terminations, verified proper voltage supply to both units, and restored power to water heaters. Both units operational upon completion of electrical repairs.

Completed comprehensive care plan tune-up on attic-mounted heat pump and air handler system. Performed system diagnostics, verified airflow and temperature differential at supply register using digital measuring instruments, and inspected ductwork and equipment installation. All components operating within manufacturer specifications, with customer providing their own 16x16x1 and washable filters as part of ongoing maintenance protocol.

Completed first-year warranty repair on geothermal flow center by replacing a weakened fitting connection toward the loop field that may have been compromised during the original installation of the new flow center. Flushed the entire system using flush cart to ensure proper operation and remove any debris. All necessary materials and tools were retrieved from shop inventory to complete the repair, with photographic documentation taken of the mechanical room installation including the flow center, associated piping, electrical junction boxes, and system components.

Completed routine AC tune-up maintenance on dual geothermal system with units located in attic and basement, both approximately 10 years old. Performed comprehensive electrical diagnostics using multimeter to test control circuitry, wiring connections, and system components. Evaluated thermostat operation and noted potential thermostat malfunction requiring replacement. Installed customer-supplied air filters (20x30x1 and 24x30x1). Inspected all electrical connections, control boards, and wiring harnesses for proper operation. System tested and operational upon completion.

Returned to property to address accessibility concerns regarding downstairs zone ductwork. Located and accessed crawl space entry point through dedicated exterior access panel. Conducted thorough inspection of supply ducting for downstairs zone, which is partially buried in dirt floor with compromised insulation throughout crawl space. Documented conditions with photographs showing exposed floor joists, scattered fiberglass insulation, and flexible ductwork running through space. Measured airflow at downstairs registers and confirmed reduced performance due to dirty 20x24x1 filter and compromised duct conditions. Reviewed all findings and photographic documentation with property owner to provide complete system evaluation.