Plumbing in Nicholasville, KY

Installed Aprilaire E130 whole-home dehumidifier in crawl space with ducted configuration. Ran 10-inch R8 insulated flex duct for supply and return connections, secured with two 10-inch tab-in collars to integrate unit with existing HVAC system. Installed PVC condensate drain line routing to appropriate drainage point and mounted unit on four cinder blocks for proper elevation and stability above crawl space floor.

Completed commercial rooftop unit replacement on flat roof membrane system. Coordinated crane service to remove existing equipment and position client-provided Carrier RTU onto weathered rooftop curb. Installed miscellaneous materials including electrical disconnect, verified proper mounting and securing of unit to existing platform, completed all electrical connections, and documented installation with photographs per contract requirements.

Responded to no cooling complaint on 20-year-old electric air conditioning system serving main level of residence. Performed comprehensive system evaluation of outdoor condensing unit and indoor air handler located in basement. Documented current equipment condition including weathered outdoor unit with debris accumulation and existing Honeywell thermostat. Based on system age exceeding manufacturer life expectancy and non-operational cooling status, provided full HVAC replacement estimate as GREEN option for complete system upgrade.

Conducted on-site evaluation for whole home dehumidifier installation. Assessed existing HVAC system configuration and inspected crawlspace infrastructure including ductwork routing, available mounting locations, and electrical access points. Documented current thermostat setup and evaluated integration requirements for humidity control equipment with existing climate control system.

Completed full residential HVAC system replacement with installation of a RUUD 3.5 ton, 14.3 SEER2 two-stage heat pump system consisting of RP14AY42AJ2NA outdoor unit and RH2TY4821STANNJ air handler with 15kW auxiliary heat kit. Removed and properly disposed of existing equipment, secured all applicable permits, and installed new system in attic space with outdoor condenser positioned on equipment pad against exterior brick wall. Installation included non-fused disconnect, electrical whip, refrigerant line set with service valves, filter rack, auxiliary drain pan, condensate safety switches, E-Z-Trap with brush, and wireless-compatible digital thermostat for zone control capability. System was charged, tested, and verified operational with all safety controls functioning properly per manufacturer specifications and local code requirements.

Completed comprehensive maintenance tune-up on three-system HVAC setup consisting of two AC units with gas furnaces and one heat pump with air handler, all located in basement. Customer-supplied 16X25X1 filters were installed on all units. During inspection, identified and documented significant water damage on concrete floor near PVC condensate drain line with visible staining and mineral deposits indicating ongoing moisture issues. Inspected gas furnace combustion chamber, burner assembly, flame sensor, and heat exchanger; verified proper operation of all burners and ignition components. Checked all electrical connections, control wiring, and safety devices on each system to ensure proper functionality and code compliance.

Completed preventive maintenance tune-up on air conditioning system with gas furnace located in crawl space. Performed comprehensive system diagnostics using calibrated electrical testing equipment to verify proper voltage, amperage, and operational parameters. Inspected all accessible components, checked refrigerant levels, and confirmed system is operating within manufacturer specifications. Customer provided air filter for installation during service visit.

Completed Gold Level prepaid maintenance on single-system air conditioning unit located in basement. Performed comprehensive tune-up including system diagnostics, temperature measurements at supply register showing 73°F, and electrical testing with clamp meter revealing 9.74 amp draw on compressor circuit. Inspected capacitor connections and verified proper voltage at 0.2V differential. All electrical components operating within manufacturer specifications. Customer providing their own 20X25X3 filter for system. System operating efficiently with no issues identified during inspection.

Completed Gold Level prepaid maintenance on 3-year-old mini split system located in attic with access through bathroom. Performed comprehensive inspection and testing of unit, including temperature readings at supply vent which measured 41.3°F, confirming proper cooling operation. System operating within normal parameters with all components functioning as designed.

Completed Gold Level prepaid maintenance tune-up on single-system heat pump and air handler located in attic. Performed comprehensive inspection of HVAC equipment, ductwork, and filter housing. Customer provided filters for installation. Verified proper operation of system components, checked flexible ductwork connections and insulation integrity, and documented equipment condition with photos. System operating within normal parameters upon completion of maintenance service.

Responded to no cooling complaint on residential air conditioning system. Upon inspection, found extremely restricted airflow due to heavily clogged air filter completely saturated with dust and debris. Removed and replaced filter, which had accumulated significant buildup indicating extended period without maintenance. Inspected electrical components including dual-run capacitor rated at 45+10 MFD, 440VAC, which tested within acceptable parameters. System restored to normal cooling operation following filter replacement and airflow verification.

Completed Care Plan tune-up on air conditioning system with gas furnace indoor unit located in attic. Performed comprehensive electrical diagnostics using clamp meter, recording voltage and amperage readings to verify proper system operation. Measured current draw at outdoor condensing unit, confirming compressor and fan motor performance within manufacturer specifications at 73.5 amps. Installed new 16x25x1 air filter as included in maintenance agreement. Conducted thorough inspection of all accessible components, tested system controls, and verified proper refrigerant pressures and temperatures. All equipment operating normally with no deficiencies noted at time of service.

Completed comprehensive 60-point whole home plumbing inspection and performed tankless water heater flush service. Inspection included thorough evaluation of all accessible plumbing fixtures, supply lines, drain assemblies, and shut-off valves throughout the property. Flushed tankless water heater system to remove mineral buildup and sediment accumulation, ensuring optimal unit performance and efficiency. Documented under-sink plumbing conditions including PVC drain assemblies, P-traps, supply line connections, and shut-off valve operation. All systems found to be functioning properly with no immediate repairs required.

Responded to no cooling call on 9-year-old AC system. Found outdoor unit not running while indoor blower operated normally. Performed system reset by cycling breaker and thermostat, which temporarily restored outdoor unit operation before it shut down again. Diagnosed failed contactor preventing consistent compressor operation. Measured supply air temperature at 50°F from register and verified electrical readings at outdoor unit using clamp meter. Replaced defective contactor, restored full system operation, and confirmed proper cooling cycle.

Responded to sewage pump failure in residential basement. Upon inspection, found non-operational sewage ejector pump system serving toilet fixtures. Removed defective pump assembly and installed replacement sewage pump with new check valve and discharge fittings. Tested system operation under load conditions to verify proper cycling and discharge function. System restored to full operational status.

Completed comprehensive heat pump and air handler maintenance tune-up on attic-installed system. Performed standard preventive maintenance procedures including inspection of evaporator coil, blower assembly, refrigerant lines, and condensate drainage system. Documented significant water staining on exterior brick wall near condensate drain discharge points, indicating potential drainage concerns that may require monitoring. All accessible components inspected and system operational at time of service completion.

Completed preventive maintenance tune-up on heat pump and air handler system located in basement as part of care plan service. Inspected evaporator coil with vertical aluminum fins, verified proper operation of blower assembly, tested system performance with digital multimeter recording 44.89 reading, and documented equipment condition in insulated mechanical space. All components found operating within normal parameters with no immediate service needs identified.

Completed final phase of electrical rewire installation including mounting of all devices, fixtures, and cover plates throughout the property. Installed exterior electrical meter enclosure on building exterior wall and mounted dual-head security lighting fixture under soffit overhang with proper weatherproof connections. All work completed to code specifications and prepared for final electrical inspection.

Completed comprehensive care plan tune-up on multi-zone HVAC system including geothermal unit, geothermal split system, three air handlers, two heat pumps, humidifier #10, and steam humidifier. Performed electrical diagnostics and measurements on system components, verifying proper voltage and amperage readings at control boards and terminals to ensure optimal equipment operation.

Completed full-day commercial HVAC repair with two-person crew. Replaced three exhaust motors on rooftop units #4, #5, and #6, and replaced bearing assembly on unit #11 exhaust motor. All units tested and returned to normal operation upon completion.