Plumbing Services in Paris, KY

Responded to callback for newly installed system that would not shut off upon reaching setpoint temperature. System was overcooling to 68°F despite thermostat set at 73°F, requiring customer to disable power at breaker panel. Performed diagnostic testing and confirmed supply air temperature at 52°F and return air temperature at 69°F, indicating proper refrigerant charge and system operation. Identified thermostat control issue preventing compressor from cycling off at target temperature. Corrected thermostat wiring and configuration settings to restore proper temperature control functionality. Verified system now cycles correctly and maintains setpoint without overcooling.

Responded to pre-purchase home inspection concerns regarding ungrounded and unsafe electrical outlets in the basement. Performed comprehensive evaluation of the electrical system, including inspection of outlet boxes, wiring configurations, and grounding conditions. Identified missing ground connections at multiple receptacle locations and documented findings with photographic evidence for the real estate transaction.

Successfully installed a 24kW Generac standby generator system with 200-amp automatic transfer switch at residential property. Installation included complete electrical integration with existing service panel, proper grounding, fuel line connection, and mounting of exterior generator unit on concrete pad with appropriate clearances per manufacturer specifications. Transfer switch was installed in basement utility area with all required conduit runs and wire connections to main electrical panel, ensuring seamless automatic power transfer during utility outages. All work completed in accordance with local electrical codes, with necessary permits obtained and inspections passed. System was fully commissioned, tested for proper operation, and configured with remote monitoring capabilities to track generator performance and runtime status.

Completed full HVAC system replacement with installation of Trane 14.3 SEER2 heat pump system in attic, including 5TWR4036A100 outdoor condensing unit, 5TEM4B04AC31 air handler, and BAYHTR1510B backup heat strip. Removed and properly disposed of existing equipment per code compliance requirements. Installed outdoor unit on pad with proper clearances and secured all refrigerant line sets and electrical connections. Mounted air handler in attic with appropriate supports and drainage provisions. Ran new refrigerant lines with proper insulation and installed exterior disconnect box with conduit on brick wall exterior. Pulled vacuum on refrigerant system and performed leak test to verify system integrity. Charged system to manufacturer specifications and verified proper refrigerant pressures and temperatures using digital manifold gauges. Tested all electrical connections, verified proper amperage draw, and confirmed heat pump operation in both heating and cooling modes. Checked airflow, te

Responded to fire department report of possible propane leak at oven location in building under construction. Upon arrival, gas supply was already shut off. Performed visual inspection of exposed gas piping system, including black iron and copper lines running through unfinished structure. Inspected connections at appliance location and traced gas distribution lines throughout accessible areas of the construction site. No active leak detected at time of inspection with gas supply in off position. Documented existing gas line configuration and condition with photographs for reference.

Responded to emergency call for leaking A.O. Smith water heater (serial #2229130323637) experiencing severe overflow from top of unit. Upon arrival, confirmed active leak flooding from upper portion of tank, requiring homeowner to shut off main water supply to entire property. Diagnosed failed water heater tank requiring complete unit replacement under manufacturer warranty through Lowe's/A.O. Smith. Disconnected all copper supply and discharge piping, electrical connections, and pressure relief valve from failed unit. Removed defective water heater from basement mechanical room. Obtained replacement water heater from Lowe's using Return Authorization #R14862859 for warranty exchange. Installed new A.O. Smith water heater, reconnecting all copper plumbing lines, valves, electrical supply, and pressure relief valve per manufacturer specifications and local plumbing code. Tested all connections for leaks, verified proper electrical operation, and restored full water service to property i

Completed full system installation of new Lennox 14.3 SEER2 5-ton air conditioning unit (model ML14KC10060-230) with matching evaporator coil (model CK40CT-60C-230) to replace existing equipment. Removed and properly disposed of old HVAC system per code requirements. Installed outdoor condenser unit on pad with new electrical disconnect box, whip kit, and insulated refrigerant lines with filter drier. Mounted indoor evaporator coil with transition to existing ductwork and installed SS2 coil drain safety water sensor for overflow protection. Installed new T10 thermostat with remote sensor for enhanced temperature control and zoning capability. Ran complete system diagnostics using manifold gauges to verify proper refrigerant charge, pressures, and temperatures across both indoor and outdoor units. Tested all electrical connections, verified proper amperage draw, and confirmed system operation through complete cooling cycle. Obtained all applicable permits and ensured installation meets

Conducted on-site electrical assessment for Kohler generator installation. Evaluated existing electrical panel capacity and circuit breaker configuration to determine compatibility with proposed standby generator system. Documented current electrical infrastructure including main service panel layout with dual rows of circuit breakers and existing conduit routing. Assessed exterior installation location near property perimeter fence, identifying vegetation clearance requirements and optimal placement for generator pad and transfer switch connection. Photographed electrical panel specifications and proposed generator location to develop comprehensive installation estimate.

Completed preventive maintenance tune-up on heat pump system with air handler located in attic accessible via pull-down stairs. Performed comprehensive system diagnostics on outdoor unit using refrigerant manifold gauge, confirming R410A refrigerant charge with pressures reading 117.3 psig low side and 229.0 psig high side, with superheat and subcooling measurements recorded. Verified thermostat operation and programming on Honeywell ProSeries digital control set to 67 degrees.

Responded to service call for inadequate cooling affecting entire residence with 20-year-old packaged AC unit. Upon arrival, performed comprehensive system evaluation of exterior-mounted heat pump/air conditioning system. Conducted visual inspection revealing weathered cabinet with aging components consistent with unit age. Assessed airflow through intake grilles and top discharge panel, checked refrigerant levels, tested electrical connections, and evaluated compressor operation. Determined system performance limitations due to age-related component degradation. Provided homeowner with findings and recommendations for addressing cooling deficiency.

Responded to no cooling call on electric air conditioning unit located in back barn. Upon inspection, found failed run capacitor with visible heat damage to connected wiring and significant debris accumulation within electrical compartment. Replaced defective capacitor, cleaned electrical connections, removed dust and lint buildup from control panel, and verified proper system operation with all components functioning normally.

Responded to no cooling complaint on electric air conditioning system with indoor unit located in basement. Upon arrival, performed diagnostic evaluation of system blowing room temperature air. Inspected outdoor condensing unit and indoor air handler components. Identified issue preventing proper cooling operation. Completed necessary repairs to restore system functionality. System tested and verified operating within normal parameters with proper cooling output prior to departure.

Responded to service call for non-operational dampers on a 15-year-old dual-zone air conditioning system with two thermostats. Inspected zone control board and damper motor wiring connections, verified system cooling capability remained intact while dampers failed to respond to zone calls. Documented control board condition and wiring configuration for future reference, advised customer of damper motor malfunction requiring replacement to restore proper zone functionality.

Completed full residential HVAC system replacement including installation of Lennox ML14KC1-030 2.5 ton 14.3 SEER2 air conditioner with outdoor disconnect and pad, Lennox EL297DF090XE48C 97% AFUE 88,000 BTU downflow two-stage gas furnace, and matching evaporator coil. Removed existing roof venting system and installed new PVC concentric vent termination, installed new refrigerant lineset with insulation and filter drier, added SS2 coil drain safety sensor with condensate drainage system, installed WiFi thermostat, outdoor electrical whip with disconnect box, gas shutoff valve with flexible connector, electrical shutoff switch, flame rollout protection, air filter rack, and all required transitions to existing ductwork. Removed and disposed of all existing equipment, obtained applicable permits, tested system operation and verified proper performance of all components per manufacturer specifications and local code requirements.

Completed full manufacturer warranty replacement of Daikin HVAC system including side discharge heat pump (Model DH9VSA4810), air handler (Model DFVE60DP1300), heat kit (Model HKTSD20DB), and Daikin One thermostat controller (Model DTST-TOU-A). Removed existing failed equipment and returned to shop per warranty protocol. Flushed refrigerant lines with dry nitrogen to ensure system cleanliness and prevent contamination. Installed new equipment in side yard location on existing concrete pad against brick exterior wall. Connected all electrical conduits and refrigerant lines, verified proper mounting and secure fittings. Performed complete system startup procedures including refrigerant charge verification, airflow measurements, and electrical connections testing. Confirmed all operating parameters within manufacturer specifications for optimal performance and warranty compliance.

Responded to request for dedicated circuit installation to garage electrical box. Evaluated existing residential electrical panel containing 28 breaker positions with mix of standard and GFCI/AFCI breakers. Assessed available capacity and breaker positions to determine feasibility of adding new dedicated circuit for garage application.

Completed semi-annual planned maintenance visit on 15 HVAC systems across multiple buildings including main house with 6 geothermal units, office with 3 systems, two guest houses with 1 system each, farm manager house with 2 systems, chapel with 1 system, and wine cooler. Performed filter changes throughout property using specified sizes (11- 20x25x4, 1- 16x25x5 Lennox X6670, 2- 20x20x1, 1- 12x20x1). Conducted spring A/C coil cleaning on all units. Serviced kitchen exhaust fan including lubrication and obtained fan belt size for future replacement. Installed RGF Lucidium BLU QR Quick Release UV treatment system on A/C coil as photographed in attic space. Inspected and verified proper operation of pressure gauges, copper refrigerant lines, and connection points on outdoor equipment. All systems tested and operating within normal parameters upon completion of maintenance.

Performed annual maintenance service on three tankless water heaters including complete system flush to remove mineral buildup and ensure optimal performance. Replaced water filter cartridges using customer-supplied units, documented filter specifications (blue cylindrical whole-house filter housing with white end caps) for future service reference, and verified all plumbing connections and valves for proper operation throughout the system.

Responded to service call for non-functional toilet with disabled flush handle. Upon arrival, found water supply had been shut off due to previous flooding incident that occurred when toilet was lifted. Assessed toilet condition and accessibility features, noting wall-mounted tank configuration with safety grab bar installation. Inspected flexible water supply line connection and verified shut-off valve position. Documented existing conditions including floor tile wear patterns and overall fixture placement in accessible bathroom setting.

Responded to warranty callback for bathroom faucet experiencing increased leakage and handle malfunction following previous repair attempt. Upon inspection, confirmed steady stream leak and handle rotating beyond normal range of motion, indicating internal component failure. Homeowner warranty approved labor coverage for faucet replacement with customer-supplied fixtures.